Manual Gardena AquaContour automatic - 8133 (page 15 of 70) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish)

820996

Zoom out

Zoom in

1/70

3: Erratic spray-range changes must be avoided.

The smaller the angle α, the greater the devia-

tion from the programmed contour is.

3.3 Install ground marker in ground

[ Fig. I2 ]:

The Large-Area Irrigation AquaContour auto-

matic is equipped with 2 ground markers and

two programs so it can be used in two differ-

entlocations, e.g in front of and behind the

house, or with very large areas. To ensure that

the locations selected can be pinpointed again,

the large-area irrigation has to be fixed on the

ground markers with removable spikes. The

2spikes provided are attached to the bottom

of the large-area irrigation. The ground marker

should always remain in the ground.

1. Select correct location for large-area irrigation

(see above).

2. Insert ground marker 7 into soil at this point

level with the ground.

3. Place large-area irrigation on ground marker 7.

4. Insert 2 spikes 8 in openings 9 of the large-

area irrigation.

The large-area irrigation is fixed in place on the

ground marker.

3.4 Connect Large-Area Irrigation

AquaContour automatic [ Fig. I3 ]:

The Large-Area Irrigation AquaContour auto-

matic can be connected to the water supply via

the Original GARDENA System. The minimum

operating pressure is 1 bar. If the other pro-

gramme is used then the sector-stops must

be correspondingly set anew.

1. Fit GARDENA Hose with connection system to

the connection q of the large-area irrigation.

2. Set sector-stops as per the location in question

(see 4. OPERATION Select watering sector).

3. Select programme (see 4. OPERATION

Start / end watering).

4. Open supply.

4. OPERATION

4.1 Select watering sector [ Fig. O1 ]:

A watering sector from 25° to 360° can be

selected. To prevent areas being watered unin-

tentionally (e.g. house), the sector should first

be selected roughly (slightly too small).

4.1.1 Roughly select sector:

1. Close water supply.

2. Turn the nozzle head w by hand to the middle

of the watering sector (e. g. P4).

3. Roughly select watering sector: turn right sector

stop ß

R to right-hand side (e. g. P9) and left sec-

tor stop ß

L to left-hand side (e. g. P2).

Note: When the water supply is open, the

sector-stop is shifted during switching of the

turn direction to its end position.

4.1.2 Re-adjust sector:

1. Open water supply.

2. Watch watering sector and re-adjust the sec-

tor-stops ß

L and ß

R according to the sector limits

(P1 and P10) until the change in direction

matches the required irrigation limits. If watering

in a complete circle, the two sector stops ß

and ß

R must be completely pushed together

between P1 and P10.

Anti-vandal device:

If the nozzle head is violently turned over the

sector-stops then the vandalism protection is

triggered. As soon as the water supply is open,

the sprinkler moves in one direction until the

set sector has been achieved again.

4.2 Programme contour points of

irrigation sector [ Fig. O2 / F1 / O3 ]:

The watering sector has to be selected before

programming. Two programmes for different

locations can be programmed in. Up to 50 con-

tour points can be programmed with the Large-

Area Irrigation AquaContour automatic. The

more points that are programmed, the more

precisely the contour will be described (e. g. with

a circular arc P7 – P10).

DANGER!

Risk of suffocation!

Small parts can be easily swallowed. There is

also a risk that the polybag can suffocate tod-

dlers.

v Keep toddlers away when you assemble the

product.

2. FUNCTION

1Menu button: Choose between program-

ming mode (Set 1 or 2)

and operating mode

(Auto 1 or 2).

2„+“ button: Increases irrigation range.

3„−“ button: Decreases irrigation range.

4OK button: Stores the irrigation range

selected.

5Set LEDs: Indicate programming

mode 1 or 2.

6Auto LEDs: Indicate automatic operating

mode 1 or 2. LED 1 or 2

flashes every 10 seconds.

3. INITIAL OPERATION

The large-area irrigation must be positioned

at apoint in the watering sector from which

it ispossible to water the entire garden area

required. The maximum range is 9 m (with 2 bar

flow pressure at the irrigation unit).

3.2.2 Incorrect location:

1: No obstacles (e.g. walls, trees, etc.) should

be located in the watering sector. It must be

pos sible to access every contour point of

the areas to be watered in a straight line. With

the maximum range the spray height can

reach approx. 5 m.

2: The minimum range is 2.5 m (at 2 bar). With

circle water distribution the large-area irrigation

must therefore be located 2.5 m from the edge

in all directions >. If this is not possible the

large-area irrigation should be positioned at the

edge and the watering area will be a circle

sector Y.

GAR_08133-20.960.11_2024-06-05.indb 15GAR_08133-20.960.11_2024-06-05.indb 15 05.06.24 11:2005.06.24 11:20

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gardena AquaContour automatic - 8133 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3.26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gardena AquaContour automatic - 8133 Manual

Product: