22873
29
Zoom out
Zoom in
Previous page
1/49
Next page
29
ENGLISH
6 - START UP
1Tap
2 Hot Water Outlet Button D90
3 Hot Water Outlet Switch E90
4 Machine on/off indicator
5 Gas on/off valve
6 Main switch
7 Right Vaporiser Tap
8 Left Vaporiser Tap
9 Cup-warmer switch
10 Boiler pressure gauge
11 Pump pressure gauge
12 Boiler level indicator
13 Right Vaporiser Pipe
14 Left Vaporiser Pipe
15 Hot Water Outlet Pipe
16 Unit D90 Control Keyboard
17 Unit E90 Control Keyboard
18 Hot Water Outlet Indicator
19 D90 Delivery Led
20 E90 Delivery Led
Once the water, gas and electrical connections have been made,
proceed to start up the machine.
Open the mains water supply tap (A).
Close the protection switch (D)
Position the machine main switch (8) to position the machine
on indicator will come on (3).
The auto-levelling device will come into operation so that the water
reaches a normal level in the boiler (12). Also press lever of water
supply tap (1) for a faster operation.
Position the main switch (6) to position for operation at
normal power or to position for operation at full power, thereby
powering the resistances.
Wait for the pressure to reach its operational pressure 1.1÷1.3 atm
checking the boiler pressure on the gauge (10).
Should the machine fail to stabilize on the indicated values it is
necessary to calibrate the pressure switch as described in paragraph
6.2.
In the event of a machine featuring a gas heating system, it is
necessary to switch on the gas by operating the gas valve (4) after
operating the main switch (6), keeping the piezoelectric switch
pressed (5) until the gas remains on.
Then check the pressure on the pump gauge (11) putting a unit into
operation with filter holder engaged filled with ground, dosed and
pressed coffee in order to achieve an effective working pressure of
8/9 atm.
Should re-calibration of the pump pressure be necessary this
operation should be undertaken as indicated in paragraph 6.3.
The machine is now ready for use.
6.1 LONG COFFEE GIGLEUR
The machine is fitted with a gigleur ( 1 per unit) with a clearance of
0.6 mm (Cod.26G0074/01).
For greater coffee delivery speed, in the case of long coffees, no.2
gigleurs are also included with the machine (complete with seals)
with a clearance of 0.8 mm (Cod.26G0073/01).
The gigleur is located in the exchanger supply fitting (1 per group).
IMPORTANT
Do not press the hot water delivery switch or button (2)
before the correct working temperature of 1.1 atm is
reached, as indicated on the boiler gauge (10).
5
4
12
1
2
17
20
1819
16
10
7
6
13
14
15
11
8
3
9
Fig.6.01
Fig.6.02
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggia E90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggia E90 in the language / languages: English as an attachment in your email.

The manual is 4,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info