718558
11
Zoom out
Zoom in
Previous page
1/84
Next page
5
ENGLISH
4. Preliminary operations
Make sure to read the “3. Safety” chapter.
4.1 Positioning
To facilitate the use of the machine, it should be placed in an appropriate location that
provides adequate space to operate.
Working spaces
L1 L2 W1 W2 H1
150 mm 221 mm 430 mm 150 mm 340 mm
Unpacking and placement
The original packaging was designed and produced to protect the machine while
being moved; it is recommended to keep it, in case the machine needs to be moved
again.
>
Remove the machine from its packaging.
>
Choose a secure and horizontal surface away from heat sources and out of the
weather, in a sufciently lit and hygienic room, next to an easily accessed power socket.
>
Position the machine allowing for working spaces.
4.2 Water tank lling
>
Lift the lid of the water tank.
>
Lift the water tank by its handle.
>
Rinse the water tank with cold water.
Do not ll the water tank with hot, boiling or carbonated water or with other liquids
that might damage the tank and the machine. Use fresh water every time you use
the machine.
>
Fill the water tank with fresh cold water to the MAX level.
> Put the tank back into the machine, checking that it is fully settled.
4.3 Coffee bean hopper lling
> Lift the coffee bean hopper lid.
Do not place too many coffee beans in the coffee bean hopper, so as to avoid
damaging grinding performance.
Coffee powder, soluble coffee, raw coffee and other substances, if placed in the coffee
bean hopper, may damage the machine. Always ll the coffee bean hopper with roasted
coffee beans only. Do not ll it with green, caramelised or avoured coffee beans.
> Pour the coffee beans slowly in the coffee bean hopper and close the lid.
4.4 Plug in and start
> Insert the plug into the socket located on the back of the machine.
> Insert the plug at the other end of the power cord into a wall socket with suitable
power voltage, as shown in the tag inside the service door.
> Turn the main switch to the ON position to turn the machine on.
> The STAND-BY button is ashing. Press the button to turn on the machine. The
display shows that it is necessary to prime the circuit: proceed as described in the
“5.2 First start” chapter.
Keeping the STAND-BY button pressed for over 8 seconds causes the DEMO MODE
function to start. To exit the demo mode, turn the machine OFF and ON using the
main switch.
L1
L2
W1
W2
H1
MAX
CALC
CLEAN
MAX
C
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggia Anima at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggia Anima in the language / languages: English, German, Italian as an attachment in your email.

The manual is 32,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggia Anima

Gaggia Anima User Manual - French, Portuguese, Spanish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info