566460
9
Zoom out
Zoom in
Previous page
1/94
Next page
9
RADIO INSTALLATION
Follow these guidelines to properly mount the servos, receiver and battery.
Make certain that the alignment tab on the battery, switch and servo connectors are oriented correctly and
                
them in. When unplugging connectors never pull directly on the wires. Instead, pull directly on the plastic
connectors. Doing so will prevent any damage to the wires.
If any servo wires are not long enough to reach the desired connection point, Futaba offers a complete range
of servo extensions which may be purchased separately for this application.
Servo
Rubber
grommet
Servo
Rubber
grommet
Always mount the servos with the supplied rubber grommets. Do
not over-tighten the screws. No part of the servo casing should
contact the mounting rails, servo tray or any other part of the
airplane/helicopter structure. If they do so, vibration will be
transmitted to the servo itself causing premature wear and/or servo
failure.
Note the small numbers (1-4) molded into each arm of the Futaba 4-arm servo arms. The
         
used to correct slight manufacturing deviances between servos and ensure the proper
geometric set-up for the aircraft.
To center the servos, connect them to the receiver and turn on
the transmitter followed by the receiver. Center the trims on the
   
degrees) to the pushrod when placed on the servo.
After the servos are installed, operate each servo over its full travel and check that the pushrods and servo
arms do not bind or contact each other. Also, make sure that the controls do not require excess force to
operate. If there is any objectionable buzzing sound coming from a servo, there is probably too much

Use the mounting plate from the receiver on/off switch as a template for the cutout and screw holes.

be inadvertently turned on or off during handling or storage of the aircraft. The cutout should allow for
a full range of motion from the switch in both directions. Be certain that the switch moves without and

When you install the switch harness in the helicopter, please use the switch cover. Generally, sandwich
the frame by the switch and switch cover and securely tighten the screws. Different models might require
different installations. In that case, please follow the directions supplied by the manufacturer.
9


Need help? Post your question in this forum.

Forumrules
1

Forum

futaba-t6j---2.4ghz

Reset search

  • Sorry my bad english, did you have the manual in spanish? Submitted on 6-10-2021 at 05:09

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T6J - 2.4GHz at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T6J - 2.4GHz in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info