520093
24
Zoom out
Zoom in
Previous page
1/127
Next page
24
<Basic Operation>
BASIC OPERATION
Battery Charging
Before charging batteries, read the "Cautions for
handling battery and battery charger" in the section
"For your safety".
How to charge the Lithium Ion battery
L
T2F2200 for the transmitter
Danger
The Lithium Ion battery LT2F2200 is only for
the transmitter T14MZ. Do not use this battery
for other equipment.
Be sure to use the battery charger LBC-1D5 for
charging the battery.
In case of charging the battery as it is installed
in the transmitter, use the optional battery
charger CR-2500 for 12V.
[Method of charging battery]
to AC Outlet
●Li-ion Battery
LT2F2200
●Special Charger
LBC-1D5
1. Connect the power cable to the charger.
2. Connect the power cable of the charger to
the wall socket (AC outlet).
* The power lamp turns on.
3. Mount the battery and then slide the battery
in the direction shown in the figure until you
hear a locking sound.
*The charge-lamp turns on and then charging starts.
4. When the charge-lamp turns off, it means
charging has been completed.
*Be sure to remove the power cable from the wall socket
after using a battery charger.
*It takes about two and a half hours for charging the battery
pack that has been used full extent. However, the charging
time may vary depending on the surrounding temperature
and the condition of the battery pack.
*
The charge lamp blinks (means error) if the battery is
improperly mounted or the battery itself is a defective
product. In such a case, please remount the battery or use
another battery.
*If you mount a charged battery, the charge lamp will turn on
for several seconds, but it will turn off later.
How to charge the Ni-Cd battery NR4F1500 for
the receiver
Use the battery charger FBC-32A that is included
in the set. In addition, you can use a rapid battery
charger for Propos that are available in the market.
[Method of charging battery]
AC Outlet
●Ni-Cd Battery
NR4F1500
●Special Charger
FBC-32A
1. Connect the power cable of the charger to
the wall socket (AC outlet).
2. Connect the connector to the NiCd battery.
*Confirm that the charging indicator, LED lamp, is on.
3. Remove the battery as soon as 15 hours has
been consumed for charging the battery.
*Battery charging will not automatically stop. Remove the
battery from the charger and remove the charger from the
wall socket.
*It is recommended to reactivate the battery by repeating
charging and discharging several times if the battery has not
been used for a long period.
*In
case of NiCd battery, you may find the poor performance
of the battery if you have used the battery only for a short
period or if you repeat charging while the battery is not fully
discharged. It is recommended to discharge the battery to the
recommended level after your usage. It is also recommended
to charge the battery just before your usage.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T14-MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T14-MZ in the language / languages: English as an attachment in your email.

The manual is 13,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T14-MZ

Futaba T14-MZ Quick start guide - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info