Manual Futaba T10 CAG (page 68 of 119) (English)

450995

Zoom out

Zoom in

1/119

LINEAR PROGRAMMABLE MIXES (

PROG.MIX1-4

Sample reasons to use linear programmable mixes:

• To correct bad tendencies of the aircraft (such as rolling in response to rudder input).

• To operate 2 or more servos for a single axis (such as two rudder servos).

7RDXWRPDWLFDOO\FRUUHFWIRUDSDUWLFXODUDFWLRQVXFKDVORZHULQJHOHYDWRUZKHQÀDSVDUHORZHUHG

7RRSHUDWHDVHFRQGFKDQQHOLQUHVSRQVHWRPRYHPHQWLQD¿UVWFKDQQHOVXFKDVLQFUHDVLQJWKHDPRXQWRIVPRNHRLOLQ

response to more throttle application, but only when the smoke switch is active).

7RWXUQRIIUHVSRQVHRIDSULPDU\FRQWUROLQFHUWDLQFLUFXPVWDQFHVVXFKDVVLPXODWLQJRQHHQJLQHÀDPLQJRXWRQDWZLQ

or throttle-assisted rudder turns, also with a twin).

Adjustability:

• Defaults: The 4 programmable mixes default to the most frequently used mixes for simplicity. If you want to use one of

these mixes, simply select that mix number so that the master and slave servos are already selected for you.

•

PROG.MIX1

aileron-to-rudder for coordinated turns

•

PROG.MIX2

HOHYDWRUWRÀDSIRUWLJKWHUORRSV

HELI

mixes default to elev-to-pitch.)

•

PROG.MIX3

ÀDSWRHOHYDWRUWRFRPSHQVDWHSLWFKLQJZLWKÀDSV

HELI

mixes default to pitch-to-elev.)

•

PROG.MIX4

throttle-to-rudder ground handling compensation

•Channels available to mix: All four mixes may use any combination of CH1-8. (CH9-10 are not proportional and cannot

be mixed.) Offset and dials may also be set to the master channels. (see below.)

•Master: the controlling channel. The channel whose movement is followed by the slave channel.

•Another channel: Most mixes follow a control channel. (Ex: rudder-to-ailerons, 25%, no switch, corrects roll

coupling.)

MASTER SLAVE LINK TRIM SWITCH POSITION RATE OFFSET

RUDD AILE ON OFF

ANY

NULL 25% 0

•Offset as master: To create an

OFFSET

PL[ VHWWKHPDVWHUDV2)67([PRYHÀDSHURQV DVÀDSVRIWKHLUWRWDO

throw when SWITCH C is in down position.)

MASTER SLAVE LINK TRIM SWITCH POSITION RATE OFFSET

OFST FLAP ON

1$

C DOWN 20% 0

•

Dial as master: To directly effect one servo’s position by moving a dial, set the master as the desired dial.

(Ex: create a second throttle trim on left slider.)

MASTER SLAVE LINK TRIM SWITCH POSITION RATE OFFSET

VR(D) THRO OFF

1$ ANY

NULL 5% 0

•Slave: the controlled channel. The channel that is moved automatically in response to the movement of the master

channel. The second channel in a mix’s name (i.e. aileron-to-rudder).

•Link: link this programmable mix with other mixes.

Ex: PMIX

FLAP-ELEVATOR

PL[LQJWRFRUUHFWIRUEDOORRQLQJZKHQÀDSVDUHORZHUHGEXWPRGHOKDVD9WDLO:LWKRXW

LINK

Your 10CG contains four separate linear programmable mixes. (Note that mixer

#5-8’s mixing

RATEs

are set with a 5-point curve.

HELI

has mixer #5-6's mixing.

see CURVE MIXES, p. 71.)

There are a variety of reasons you might want to use these mixes. A few are

listed here. All of the adjustable parameters are listed below, but don’t let them

VFDUH\RX)RU\RXU¿UVWIHZ WLPHVH[SHULPHQWLQJZLWKPL[HV MXVWWXUQRQWKH

default mixes, adjust them how you think they need to be, then use the servo

screen to check and see if you were correct. As with all functions, a sample

setup follows, step by step, to assist you.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba T10 CAG Manual

Product: