450995

Futaba T10 CAG Manual

49
Zoom out
Zoom in
Previous page
1/119
Next page
49
SUB-TRIM
: makes small changes or corrections to the neutral position of each servo. Range is -120 to +120, with 0 setting,
the default, being no
SUB-TRIM
.
We recommend that you center the digital trims before making
SUB-TRIM
changes, and that you try to keep all of the
SUB-TRIM
values as small as
possible. Larger
SUB-TRIM
values affect the servo's range of travel is restricted
on one side.
The recommended procedure is as follows:
• measure and record the desired surface position;
• zero out both the trims (
TRIM RESET
menu) and the
SUB-TRIMs
(this menu);
• mount servo arms and linkages so that the control surface’s neutral is as correct as possible; and
• use a small amount of
SUB-TRIM
WRPDNH¿QHFRUUHFWLRQV
GOAL of EXAMPLE: STEPS: INPUTS:
Adjust the flap servo's
SUB-TRIM
until
its center exactly matches the aileron
servo's center, as they work together as
ÀDSHURQV
Open
BASIC
menu, then open
SUB-TRIM
.
for 1 second.
(If
ADVANCE
, again.)
C
to
SUB-TRIM
.
Choose the channel to adjust, and adjust
XQWLOVXUIDFHVPDWFK([ÀDS
C
to
FLAP
as needed.
C
to each channel,
Repeat for other channels.
as needed.
Close.
Where next? Adjust trim steps: see p. 48.
Adjust
END POINTs
: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO
D/R
,
EXP
): see p. 42.
The servo submenu includes two features:
• real-time bar-graph display to demonstrate exactly what commands the
transmitter is sending to the servos. (This can be particularly handy in setting
up models with complicated mixing functions, because the results of each
stick, lever, knob, switch input and delay circuit may be immediately seen.)
VHUYRF\FOH IXQFWLRQWR KHOSORFDWH VHUYRSUREOHPV SULRUWR LQÀLJKW IDLOXUHV
(channels 1-8)
GOAL of EXAMPLE: STEPS: INPUTS:
View the result of reassigning channel
6 from VR(A) knob to three-position
SWITCH C.
Cycle the channel 6 servo.
Complete desired programming
function. (Ex: in
AUX-CH
, move ch. 6 to
SWITCH C)
See
AUX-CH
for details. (p. 39.)
Open the
SERVO
function.
for 1 second.
(If
ADVANCE
, again.)
C
to
SERVO
.
Move each control to see the operation.
(Ex: SWITCH C in all positions)
C to center position.
Note change in position of ch. 6 servo.
Prepare all servos to be cycled and cycle.
Plug in servos. POWER ON.
End cycling and close.
Where next? 6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO
D/R
,
EXP
): see p. 42.
Set up desired programmable mixes: see p. 61.
Set up dual aileron servos: see p. 51.
Set up dual elevator servos: see p. 57.
SERVO
display and cycle submenu: displays radio's output to channels 1-10.
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T10 CAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info