450995

Futaba T10 CAG Manual

36
Zoom out
Zoom in
Previous page
1/119
Next page
36
Second aileron (
AILE-2
) (
ACRO
GLID 1A+1F
GLID 2A+1F
only): changes the default choice for dual aileron servos from
channels 6 (
FLAPERON
) to channels 5 and 6 or channels 3 and 6 (
GLID 1A+1F
only), or 7 (
AIL-DIF
) to channels 5 and 7.
NOTE: Changing
AILE-2
only tells the system which servos to utilize if
FLAPERON
or
AIL-DIF
is activated. You still must
activate that function and complete its setup. For details on twin aileron servos, including using
AILE-2
, see p. 55.
(
GLID 1A+1F
only): If using channel 3 for second aileron, the receiver's Battery Fail-Safe function does not work.
Adjustable travel limit (
ATL
): makes the channel 3 TRIM LEVER (THROTTLE TRIM) effective only at low throttle,
disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to
ON
.
If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set
ATL
to
OFF
. If you need the
ATL
to be effective at the top of the stick instead of the bottom, reverse the
THR-REV
setting. Note
that this affects all models in the radio, not just the model you are currently editing. See servo
REVERSE
, p. 38.
GOAL of EXAMPLE: STEPS: INPUTS:
Change
ATL
from
ON
to
OFF
for battling
robots, tanks, airbrakes and other
channel 3 uses.
Open
BASIC
menu, then open
PARAMETER
submenu.
for 1 second.
(If
ADVANCE
, again.)
to 2nd page of menu.
C
to
PARAMETER
.
Go to
ATL
and Change. (Ex: to
OFF
)
C
to
ATL
. to
OFF
.
Close.
Where next? Set up
ELEVON
IRUWDQNVW\OHFRQWUROWKURWWOHVWHHULQJRQRQH67,&.VHHS
Set up
IDLE-DOWN
and
THR-CUT
to adjust channel 3 servo at low-stick: see p. 40.
5HDVVLJQDX[LOLDU\FKDQQHOVH[IURPGLDOWRVZLWFKVOLGHUVHHS
Utilize servo
REVERSE
: see p. 38.
Adjust servo travel with
END POINT
: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO
D/R
,
EXP
): see p. 42.
LCD screen adjustment (
CONTRAST
BACK-LIGHT
):
Adjustability:
The following LCD screen adustments are possible.
• Contrast adjustment
• Backlighting brightness adjustment
CONTRAST
: adjust the LCD contrast from +10(dark) to -10(bright). Also, it is
possible to adjust the contrast from the home screen. See Adjusting Display
Contrast, p.16.
BACK-LIGHT MAX
DGMXVWVWKHEDFNOLJKWLQJEULJKWQHVVIRUWKHVSHFL¿FSHULRGDSSUR[LPDWHO\VHFRQGVDIWHURSHUDWLQJWKH
edit keys. Setting range: OFF(0) to 20(bright).
BACK-LIGHT MIN
DGMXVWVWKHEDFNOLJKWLQJEULJKWQHVVDIWHUWKHDERYHVSHFL¿FSHULRG6HWWLQJUDQJH2))WR
MAX
setting.
GOAL of EXAMPLE: STEPS: INPUTS:
Change
CONTRAST
from
0
to
+2
. Open BASIC menu, then open
PARAMETER
submenu.
for 1 second.
(If
ADVANCE
, again.)
C
to
PARAMETER
.
Go to
CONTRAST
and change setting.
(Ex:
+2
)
C
to
CONTRAST
.
to
+2
.
Close.
Throttle Reverse (
THR-REV
) (
GLID
only): is a special function that reverses the throttle control, including moving the trim
functionality to the stick's upper half.
The separate
THR-REV
settings for each model can be set. Default setting depends on the
THR-REV
setting in the
TX SETTING
menu, see p.17.
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T10 CAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info