450995

Futaba T10 CAG Manual

27
Zoom out
Zoom in
Previous page
1/119
Next page
27
A QUICK GUIDE: GETTING STARTED WITH A
BASIC
4-CHANNEL AIRCRAFT
This guide is intended to help you get acquainted with the radio, to give you a jump start on using your new radio, and to
give you some ideas and direction on how to do even more than you may have already considered. It follows our basic
format of all programming pages: a big picture overview of what we accomplish; a “by name” description of what we're
doing to help acquaint you with the radio; then a step-by-step instruction to leave out the mystery when setting up your
model.
For additional details on each function, see that function's section in this manual. The page numbers are indicated in the
goals column as a convenience to you.
See p.26 for a legend of symbols used.
GOALS of EXAMPLE STEPS INPUTS for EXAMPLE
Prepare your aircraft. Install all servos, switches, receivers, etc. per your model's instructions. Turn
on transmitter then receiver; adjust all linkages so surfaces are nearly centered.
Mechanically adjust all linkages as close as possible to proper control throws.
Check servo direction. Make notes now of what you will need to change during
programming.
Name the model.
P. 32.
[Note that you do not need to do
anything to "save” or store this data.
Only critical changes such as a
MODEL
RESET
require additional keystrokes to
accept the change.]
Open the
BASIC
menu, then open the
MODEL
submenu.
Turn on the transmitter.
for 1 second.
(If
ADVANCE
, again.)
C
as needed to highlight
MODEL
.
to choose
MODEL
.
Go to
MODEL NAME
.
C
to
NAME
.
(First character of model's name is
highlighted.)
Input aircraft's name.
Close the
MODEL
submenu.
WRFKDQJH¿UVWFKDUDFWHU
When proper character is displayed,
C
to move to next character.
Repeat as needed.
to return to
BASIC
menu.
Reverse servos as needed for proper
control operation.
P. 38.
In the
BASIC
menu, open (servo)
REVERSE
.
C
to
REVERSE
.
to choose
REVERSE
.
Choose desired servo and reverse its
direction of travel. (Ex: reversing rudder
servo.)
C
to
CH4: RUDD
.
so
REV
is highlighted.
Repeat as needed.
Adjust Travels as needed to match
model's recommended throws (usually
listed as high rates).
P. 39.
From
BASIC
menu, choose
END POINT
.
C
to
END POINT
.
to choose
END POINT
.
Adjust the servo's end points.
(Ex: throttle servo)
Close the function.
C
to
THROTTLE
.
THROTTLE STICK.
until carb barrel closes as desired.
THROTTLE STICK.
until throttle arm just opens carb
fully at full THROTTLE STICK.
Repeat for each channel as needed.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T10 CAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T10 CAG in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info