747980
32
Zoom out
Zoom in
Previous page
1/189
Next page
32
Before Use
Rubber
grommet
Brass eyelet
Wood screw
Servo mount
2.3-2.6mm nut
washer
Rubber
grommet
Brass eyelet
Servo mount
2.3-2.6mm screw
(Helicopter)(Airplane/Glider)
Servo lead wires
To prevent the servo lead cable from being
broken by vibration during flight, provide a
little slack in the cable and fasten it at suitable
points. Periodically check the cable during daily
maintenance.
Fasten about 5-10 cm
from the servo outlet so
that the lead wire is neat.
Margin in the lead wire.
Mounting the power switch
When mounting a power switch to an airframe,
make a rectangular hole that is a little larger than
the total stroke of the switch so that you can turn
the switch ON/OFF without binding.
Avoid mounting the switch where it can be
covered by engine oil and dust. In general, it is
recommended to mount the power switch on the
VLGHRIWKHIXVHODJHWKDWLVRSSRVLWHWKHPXIÀHU
WARNING
Connecting connectors
Be sure to insert the connector until it stops at
the deepest point.
How to protect the receiver from vibration and
water
Wrap the receiver with something soft such
as foam rubber to avoid vibration. If there is a
chance of it getting wet, put the receiver in a
waterproof bag or balloon to avoid water.
Receiver's antenna
Never cut the receiver's antenna. Do not bind
the receiver's antenna with the cables for
servos.
Locate the receiver's antenna as far as possible
from metals or carbon fiber components such
as frames, cables, etc.
*Cutting or binding the receiver's antenna will reduce the ra-
dio reception sensitivity and range, and may cause a crash.
Servo throw
$GMXVW\RXUV\VWHPVRWKDWSXVKURGVZLOOQRW
bind or sag when operating the servos to the
full extent.
*If excessive force is continuously applied to a servo, the
servo could be damaged due to force on the gear train and/
or power consumption causing rapid battery drain.
Mounting servos
Use a vibration-proof rubber (such as rubber
grommet) under a servo when mounting the
servo on a servo mount. And be sure that the
servo cases do not touch directly to the metal
parts such as servo mount.
*If the servo case contacts the airframe directly, vibration
will travel to and possibly damage the servo.
Mounting the Servo
6DIHW\SUHFDXWLRQVZKHQ\RXLQVWDOOUHFHLYHUDQGVHUYRV
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-32MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-32MZ in the language / languages: English as an attachment in your email.

The manual is 8,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T-32MZ

Futaba T-32MZ User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info