747980
30
Zoom out
Zoom in
Previous page
1/189
Next page
30
Before Use
A special toolbox is included with your T32MZ.
This allows you to make all of the mechanical
DGMXVWPHQWVWKDWPD\EHQHHGHG
Hexagonal wrench (1.5 mm and 2.5 mm)
7KHVHZUHQFKHVDUHIRUDGMXVWPHQWRIVWLFNVDQG
replacement of the switches.
Tool for removing switch nuts.
This is used when changing or replacing switches.
Stylus pen
A rubber cap is attached to the stylus pen/toolbox.
<RXPD\XVHWKLVVW\OXVZLWKUXEEHUFDSZKHQ
operating the touch panel. The stylus allows more
precise operation than fingers without fear of
damaging the panels surface.
ٴ<RXPD\XVHWKLVWRRO
DVDVW\OXVSHQ
Toolbox
6HUYR2SWLRQ؞7RROER[؞5HFHLYHU6ZLWFK
Receiver Switch ESW-1J
Servo (Option)
Purchase servos appropriate for their intended use.
*Analog servos may not be used when operating in the
FASSTest 12CH mode.
When operating in the FASSTest12CH mode use digital
servos, this includes all brushless and S.BUS servos.
ٴ7RROIRUUHPRYLQJ
GHFRUDWLRQQXWV
ٴ+H[:UHQFKPPDQGPP
ٴ5XEEHU&DS
ESW-1J connects a Futaba receiver to a battery and is
turned on and off in an FET circuit. Compared to using a
mechanical switch, it allows more current to be sent with
less loss.
When the model is not being used, always remove or disconnect
the battery.
When the switch is off, a slight amount of current still flows.
Unless the switch and battery are disconnected, the battery
will be damaged from excessive discharge.
Always make sure that the switch harness is firmly attached to
the fuselage of the model.
There is the danger of loss of control and crashing if the
connector is disconnected by vibration and shock.
Do not charge the receiver battery through the switch harness.
Disconnect the receiver battery and charge to the manufactures
instructions.
There is no charge connector in this switch.
Never reverse the battery polarity.
Reverse connection will immediately destroy the receiver,
servo, etc.
Ensure that the unit is mounted in an area that will eliminate
exposure to fuel, water and vibration.
As with any electronic components, proper precautions are
urged to prolong the life and increase the performance of the
ESW-1J.
Allow a slight amount of slack in the cables and fasten them at a
suitable location to prevent any damage from vibration during
flight.
Never solder the ESW-1J or attempt to repair, deform, modify or
disassemble them.
Do not use the ESW-1J with anything other than an R/C model.
Switch
Attachment
Less than 5 mm of
mounting plate
Attached screw
Switch cover
Use the mounting plate from the receiver on/
off switch as a template for the cutout and screw
holes. Mount the switch on the side of the fuselage
opposite the engine exhaust, and where it won’t
be inadvertently turned on or off during handling
or storage. Be certain the switch moves without
restriction and “snaps” from ON to OFF, and that
the cutout allows full motion of the switch in both
directions.
WARNING
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-32MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-32MZ in the language / languages: English as an attachment in your email.

The manual is 8,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T-32MZ

Futaba T-32MZ User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info