747917
99
Zoom out
Zoom in
Previous page
1/228
Next page
99
GO to TABLE OF CONTENTS
Altitude
Sets the altitude
on which the alarm
operates.
An upward arrow
indicates the alarm
will sound when the
altitude reaches above
your set value.
A downward arrow
indicates the alarm
will sound when the
altitude reaches below
your set value.
Alarm is chosen from
Buzzer, Voice, and
Inhibit.
Allows Speech to be
turned ON or OFF.
Allows Melody to be
turned ON or OFF.
Tap the [Altitude] button in the Telemetry screen to
call the setup screen shown below.
Max. and min. values
since the power
was turned ON will
display.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH /T-FHSS mode can use all the telemetry
functions.
Type 1
Type 2
Type 3
"Vibrator" type
If the following types are selected, the transmitter
will vibrate during the warning.
Telemetry : Altitude
Displaying data from the altitude
Altitude is a screen which displays / sets up the altitude
information from an optional altitude sensor or GPS sensor.
The altitude of the model which is ying can be known. If it
becomes higher (low) than preset altitude, you can be told by
alarm. Warning by vibration can also be chosen. Data when
a power supply is turned on shall be 0 m, and it displays the
altitude which changed from there. Even if the altitude of an
aireld is high, that shall be 0 m and the altitude dierence
from an airfield is displayed. This sensor calculates the
altitude from atmospheric pressure. Atmospheric pressure
will get lower as you go up in altitude. Using this, the
sensor will estimate the altitude. Please understand that an
exact advanced display cannot be performed if atmospheric
pressure changes in a weather situation.
First, the set of a reference is required.
1. The model and transmitter to which the
altitude sensor was connected are turned on.
2. Tap to the [Preset] of "Reference" item.
*Atmospheric pressure is changed according to the weather
also at the same aireld. You should preset before a ight.
Alarm set : Altitude
1. Tap Alarm and choose from Buzzer, Voice,
and Inhibit.
2. Choose "Inhibit" for Vibrator if not using the
vibrator alarm. If using vibrator, choose one
of the three types.
3. Tap to the Limit [xxx
m
] item.
4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"
buttons.
Initial value: ↑200 m ↓-50 m
Adjustment range -500 m~+3,000 m
(↑Limit
↓Limit)
*When the screen is tapped for one second, the rate is reset
to the initial value.
5. To terminate the input and return to the
original state, push the HOME/EXIT button.
*An altitude sensor or GPS sensor must be installed in the aircraft.
If this is set to Mode1-4,
a rise and dive are told
by a di󰮏erent melody.
Mode1: Little rise/dive
Melody changes
: sensitively
Mode4: Big rise/dive
Melody changes
: insensible
●Return to
Linkage menu
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info