747917
98
Zoom out
Zoom in
Previous page
1/228
Next page
98
GO to TABLE OF CONTENTS
rpm
Sets the rpm on which
the alarm operates.
An upward arrow
will show that an alarm
will sound when the
rpm rises above the set
value.
A downward arrow
will show that an alarm
will sound when the
rpm falls below the set
value.
Alarm is chosen from
Buzzer, Voice, and
Inhibit.
Allows Speech to be
turned ON or OFF.
● Tap the [ rpm sensor] button in the Telemetry screen
to call the setup screen shown below.
Max. and min. values
since the power
was turned ON will
display.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH /T-FHSS mode can use all the telemetry
functions.
Type 1
Type 2
Type 3
"Vibrator" type
If the following types are selected, the transmitter
will vibrate during the warning.
Telemetry : RPM Sensor
Displaying data from the rpm
The RPM Sensor screen is used to set up an
optional rpm sensor and display the rotation
information it transmits.
The rotation of the model (engine, motor, etc.)
which is ying can be shown.
If it becomes higher or lower than the setting, an
alarm and/or vibration will alert you.
Alarm set : Over
(
Under
)
rotations
1. Tap Alarm and choose from Buzzer, Voice,
and Inhibit.
2. Choose "Inhibit" for Vibrator if not using the
vibrator alarm. If using vibrator, choose one
of the three types.
3. Tap to the Limit [
xxx
rpm] item.
4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"
buttons.
Initial value: ↑ 2,000 rpm 0 rpm
Adjustment range: 0 rpm~150,000 rpm
(↑Limit
↓Limit)
*When the screen is tapped for one second, the rate is reset
to the initial value.
5. To terminate the input and return to the
original state, push the HOME/EXIT button.
*An rpm sensor must be installed in the aircraft.
"Magnet"
"Optics"
"Brushless motor"
SBS-01RM →
SBS-01RO
SBS-01RB →
Gear ratio
Blade
Pole
1.00~99.00
2~10
2~30
●Return to
Linkage menu
98


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info