Manual Futaba T-16IZ (page 48 of 228) (English)

747917

Zoom out

Zoom in

1/228

→ GO to TABLE OF CONTENTS

● Swash plate correction (Except H-1 mode)

*If any interactions are noticed, for a description of the

linkage correction function, please refer to the SWASH

function.

5. Throttle/Pitch curve setting

This function adjusts the throttle or pitch operation

curve in relation to the movement of the throttle

stick for each condition.

<Throttlecurvesettingexample>

Call the throttle curve of each condition with the

condition select switch.

●Normal curve adjustment

Normal curve creates a basic throttle curve

centered near hovering. This curve is adjusted

together with the pitch curve (Normal) so that the

engine speed is constant and up/down control is

easiest.

●Idle up curve adjustment

The low side Throttle curve creates a curve

matched for aerobatics (loop, roll, 3D, etc.).

●Throttle hold curve adjustment

The curve is not used when performing auto rotation

dives.

Conrm that the rate of the slowest position (0%) of

the stick is 0% (initial setting).

<Exampleofpitchcurvesetting>

Call the pitch curve of each condition with the

condition select switch.

●Pitch curve (Normal)

Make the pitch at hovering approximately +5

Set the pitch at hovering with the stick position at

the 50% point as the standard.

*Stability at hovering may be connected to the throttle curve.

Adjustment is easy by using the hovering throttle function

and hovering pitch function together.

●Pitch curve (Idle up 1)

The idle up 1 pitch curve function creates a curve

matched to airborne ight.

Set to -7

~+12

as standard.

4. Fuselage linkage

Connect the throttle rudder, aileron, elevator,

pitch, and other servos in accordance with the

kit instruction manual. For a description of the

connection method, see "Servos connection by

model type".

Note: The channel assignment of the T16IZ

is different from that of our existing systems.

(The channel assigned to each function can

be checked at the Function menu of the

Linkage menu.)

● If the direction of operation of the servo is

incorrect, use the Reverse function of the

Linkage menu. Also use the swash AFR

function in other than the H-1 mode.

● Adjust the direction of operation of the gyro.

(Gyro side function)

● Connect the throttle linkage so that the

carburetor can fully close at full trim throttle

cut.

● Adjust the neutral position at the linkage

side and ne tune with the Sub-Trim function

and End point function (rudder angle

adjustment). To protect the linkage, a limit

position can also be set with the End point

function.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba T-16IZ Manual

Product: