747917
34
Zoom out
Zoom in
Previous page
1/228
Next page
34
GO to TABLE OF CONTENTS
Output
connector
Channel
Mode A
1
8CH
Mode B
1
7CH
Mode C
9
16CH
Mode D
9
15CH
1 1 1 9 9
2 2 2 10 10
3 3 3 11 11
4 4 4 12 12
5 5 5 13 13
6 6 6 14 14
7/B 7 7 15 15
8/SB 8 S.BUS 16 S.BUS
Red LED
blink
1 time 2 times 3 times 4 times
R7108SB CH Mode table
Default
Channel Modes
The R7108SB is capable of changing its channel allocations as
described in the table below. This is especially important when
using the receiver in a dual receiver mode.
1
Turn on the receiver. [Transmitter is always OFF]
2
Press and hold the Link/Mode button for 5 seconds to 10
seconds.
3
When the LED of the receiver changes from blinking red
to blinking red with green, Link/Mode button is released.
4
The LED should now blink red two times in the patterns
described in the chart below.
5
Each press of the Link/Mode button advances the
receiver to the next mode.
6
When you reach the mode that you wish to operate in,
press and hold the Link/Mode button for more than 2
seconds.
When LED blinks in green with red, it is the
completion of a mode change, Link/Mode button is
released.
7
Please cycle the receiver power off and back on again
after changing the Channel mode.
LED Indication
System Status LED
FASSTest
No signal reception Red Solid
Receiving signals Green Solid
Waiting for link
Start → 2second
later → Red
Blink(1second)
FASST
No signal reception Red Solid
Receiving signals Green Solid
Receiving signals
but ID is unmatched
Green Blink
Waiting for link Red Blink
FASSTest
FASST
Unrecoverable error
(EEPROM, etc.)
Alternate blink
Green LED
blink
System
1 time FASSTest
2 times FASST Multi-ch Normal mode
3 times FASST Multi-ch High-speed mode
4 times FASST 7ch Normal mode
5 times FASST 7ch High-speed mode
R7108SB System table
*
FASST mode cannot use telemetry functions.
Systems(FASSTest FASST)changemethod
1
Turn on the receiver. [Transmitter is always OFF]
2
Press and hold the Link/Mode button for 10 seconds to 15 seconds.
3
When the LED begins to blink green the button may be released.
4
The LED should now be blinking green in one of the patterns
described by the chart below.
( Default : FASSTest )
5
Each press of the Link/Mode button advances the receiver to the
next system.
6
When you reach the system that you wish to operate in, press and
hold the Link/Mode button for more than 2 seconds.
When the LED
blinks green and red, the system change is complete. Release the
Link/Mode button.
7
Please cycle the receiver power off and back on again after
changing the system.
Default
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info