747917
32
Zoom out
Zoom in
Previous page
1/228
Next page
32
GO to TABLE OF CONTENTS
Link/Mode Switch
Use the small plastic screw driver that was included
with your receiver.
The Link/Mode Switch is also used for the CH
mode selection.
(The button is not used to link the transmitter and
receiver together. )
Extra Voltage Connector
Use this connector when using a voltage telemetry
device to send the battery voltage information (DC
0 ~ 70 V) from the receiver to the transmitter.
Please use the External voltage input cable.
(UBB0141) This connects directly to your main
motor batteries.
DANGER
Don't touch wiring.
* There is a danger of receiving an electric shock.
Do not short-circuit the battery
terminals.
* A short circuit across the battery terminals may cause
abnormal heating, re and burns.
Please double check your polarity (+ and
-) when hooking up your connectors.
* If + and - of wiring are mistaken, it will damage, ignite and
explode.
Don’ t connect to Extra Voltage before
turning on a receiver power supply.
Before using the receiver, be sure to read the
precautions listed in the following pages.
Connector
"1 through 6":outputs for the channels 1 through 6
"7/B": outputs of 7 channels and power.
"8/SB": outputs of 8 channels or S.BUS port.
[S.BUSSevoS.BUSGyro]
"S.BUS2": outputs of S.BUS2 port.
[TelemetrySensor]
*When using nine or more channels, use an S.BUS
function or use a second R7108SB and link both
to your transmitter.
Connector insertion
Firmly insert the connector in the direction shown
in the gure. Insert the S.BUS2 by turning it 90
degrees.
WARNING
S.BUS2connectors
Don't connect an S.BUS servo/gyro to
S.BUS2 connector.
LED Monitor
This monitor is used to check the CH mode of the
receiver.
Receiver Nomenclature
Link/Mode
Channels 1 ~ 6
Channel 7 / Battery
Channel 8 or S.BUS
S.BUS2 : Telemetry sensor
or S.BUS2 equipment
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info