747962

Futaba R7018SB Manual

4
Zoom out
Zoom in
Previous page
1/5
Next page
Link to the transmitter : FASST
1
Bring the transmitter and the receiver close to each
other, within 20 inches (half meter).
2
Turn on the transmitter and receiver.
3
Link operation is performed by the Link/Mode switch.
• When using TM-8 module, it's possible to set F/S position (only 3CH).
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold time
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Besides TM-8
Re-link(ID set)
*
Refer to the instruction manual of the transmitter or module used
for a description of the linking operation, F/S position setting
methods and other details.
When using Multi prop (MPDX-1)
The MPDX-1 can be used with FASSTest by merely
setting the corresponding transmitter. (Refer to the
instruction manual of the corresponding transmitter.)
When using the MPDX-1 Multi Prop Decoder (sold
separately) with the FASST system, change the setting by
the following method.
Enable the MPDX-1 at channels 11 and 12. (Initial value:
OFF)
Channels 11 and 12 cannot be used individually for
MPDX-1 output.
The MPDX-1 extends 1 channel to 8 channels. However,
since the response speed becomes slower and there are
functional restrictions, use it at simple switch operation
and other applications that require numerous channels.
Multi prop mode Change method
1
. Switch the receiver to the FASST system (Normal or
High-speed).
2
. Turn on the receiver power. (Transmitter power off)
3
. Press the Link/Mode switch for at least 10 seconds.
4
. When the LED blinks red and changes to red/green
simultaneous rapid blinking, release the switch.
5
. The receiver enters the multi prop mode and the LED of
the current mode blinks. (Initial value: OFF)
6
. Each time the switch is pressed, the mode changes.
7
. When the receiver was switched to the desired mode,
press the Link/Mode switch for at least 2 seconds.
8
. When the LED switches to red/green simultaneous
rapid blinking, mode switching is complete. Release the
switch.
9
. When switching is complete, turn on the power. When
the power is turned on, the receiver switches to the new
mode.
FASST
When switched, the R7018SB can use the FASST-Multi-ch mode. When the FASST system is used, the telemetry and
Extra Voltage ports cannot be used. The FASST system has a Normal mode and a High-speed mode. However, in the
High-speed mode, analog servos cannot be used at CH1
∼
6.
Green LED blink Mode
1 time
Multi prop mode OFF
2 time
Multi prop mode ON
FASSTest
FASST
When a telemetry adapter (TMA-1) is used
: FASSTest only
When using a TMA-1 (sold separately), change the
settings by the following method.
The TMA-1 is a device for viewing the telemetry data on
a smartphone or tablet.
R7018SB and TMA-1 linking method
1
. Switch the receiver to FASSTest system.
2
. Link the transmitter and receiver, and after confirming
operation, turn off the power.
3
. Turn on the receiver power. (Transmitter power off)
4
. Press the Link/Mode switch for at least 10 seconds.
5
. After the LED blinks red and changes to red/green
simultaneous rapid blinking, release the switch.
6
. The receiver enters the linked with TMA-1 mode, and
the LED begins red/green simultaneous rapid blinking.
7
. Press the TMA-1 link switch until the LED starts to blink
and wait for the TMA-1 to link.
8
. When TMA-1 linking is complete, the TMA-1 LED
changes from red to green for a moment.
9
. When linking is complete, turn on the receiver power
and check the operation of all the devices.
03';ق2SWLRQك
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
©FUTABA CORPORATION 2015, 4 (1)
R7018SB Specifications
FASSTest-2.4GHz system(18CH/12CH mode)FASST-2.4GHz system
(Multi-ch mode)
S.BUS2 and S.BUS port and Linear 16 ch +Digital 2 ch for conventional
system receiver
• Dual antenna diversity
• Size: 2.15 x 1.59 x 0.64 in. (54.6x40.4x16.3mm)
• Weight: 1.48 oz. (42g)
• Power requirement: 6.0V to 7.4V(Voltage range: 4.8 to 8.4V)
• Battery F/S Voltage: It sets up with a transmitter (F/S can't be used in
case of FASST.)
• Extra Voltage port: 0
∼
70V DC
- 4 -
All product and company names mentioned
herein are the trademarks or registered
trademarks of their respective owners.
本產品符合低功率電波輻射性電機管理辦法 第十二條、第十四條等條文規定
1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率
射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R7018SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R7018SB in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba R7018SB

Futaba R7018SB User Manual - German - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info