747962
2
Zoom out
Zoom in
Previous page
1/5
Next page
90˚
(Antenna installation)
Connector   
The direction of the connectors of the bottom 3 ports is
GLIIHUHQWE\Û
56%
&+6HUYRV
6%86VHUYRV
6%86*\URV
5HFHLYHUق6HUYRك%DWWHU\$
HJ/LSRFHOO岜9
5HFHLYHUق6HUYRك%DWWHU\%
HJ/LSRFHOO岜9
+XE
+XE
([FOXVLYHVZLWFK
6%86HTXLSPHQW
7HOHPHWU\VHQVRU
7HOHPHWU\VHQVRU
6%86
3RUW
6%86
3RUW
D
G
D
G
'RQRWFRQQHFW
DEDWWHU\WR
WKHSRUWVDW
WKLVVLGH
%DWWHU\
FRQQHFWRU
Do not use a battery of the
wrong rated voltage and
type (Li-po, Li-Fe, etc.).
When the receiver is not in
use, always disconnect the
battery.
WARNING
Never reverse the battery polarity.
A reverse connection the battery terminals may cause
abnormal heating, fire and burns.
Do not short circuit the battery terminals.
A short circuit across the battery terminals may cause
abnormal heating, fire and burns.
Be careful when soldering to the plug; don't overheat
the plug with your soldering iron and take great care to
avoid short-circuits on the plug.
Such a overheat and short-circuit would destroy the plug.
LED Indication
System Mode LED Status Link LED
FASSTest Green Solid
No signal reception Red Solid
Receiving signals Green Solid
Waiting for link
Start 2second later Red
Blink(1second)
FASST Off
No signal reception Red Solid
Receiving signals Green Solid
Receiving signals but ID is unmatched Green Blink
Waiting for link Red Blink
FASSTest
FASST
Unrecoverable error (EEPROM, etc.)
Alternate blink
*Fixed at neutral if a servo is connected to a port other than a usable
transmitter channel.
*The telemetry and Extra Voltage ports cannot be used with the
FASST system.
FASSTest FASST (Normal-High-speed
Change method
1
. Turn on the receiver.
Transmitter OFF
2
. Press and hold the Link/Mode button for more then 5 second.
3
. When the LED begins to blink green/red the button may be
released.
4
. The LED should now be blinking red in one of the patterns
described by the chart below.
( Default : FASSTest )
5
. Each press of the Mode/Link button advances the receiver to
the next mode.
6
. When you reach the mode that you wish to operate in, press
and hold the Mode/Link button for more than 2 seconds.
7
. Once locked into the correct mode the LED will change to a
solid color.
8
. Please cycle the receiver(s) power off and back on again
after changing the Channel Mode.
Red LED blink System
1 time FASSTest
2 time
FASST Multi-ch
Normal mode
3 time
FASST Multi-ch
High-speed mode
Connection
Female Deans Ultra Plug
Soldering
Battery Wire
Heatshrink
tube
- 2 -
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R7018SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R7018SB in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba R7018SB

Futaba R7018SB User Manual - German - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info