747922
165
Zoom out
Zoom in
Previous page
1/183
Next page
165
Model Menu (Helicopter Functions)
Pitch Rudder (Revolution mixing)
Use this mix when you want to suppress the
reaction torque generated by main rotor pitch and
speed changes during pitch operation. Adjust so
that the nose does not move in the rudder direction.
An acceleration function which temporarily
increases the correction rate at throttle stick
acceleration/deceleration operation can be set. The
mixing rate at acceleration/deceleration can be set.
Setting method
ŏ When using this function, Tap [INH]. (ON is
displayed.)
ŏ When you want to set the same contents at
other conditions, select the group mode.
When you want to set the selected condition
only, select the single mode (initial setting).
ŏ A mixing curve is set.
<Normal condition mixing curve>
The mixing curve rate starts from a small
value.
For a rotor with a clockwise operation
direction (polarity), when pitch was
operated at the plus side, set so that
mixing is in the clockwise direction. First,
trim at hovering and then adjust the
neutral position.
1. Adjustment between slow and hovering
Repeatedly hover from take off and land
from hovering at a constant rate matched
to your own rhythm, and adjust the pitch
so the nose does not deflect when the
throttle is raised and lowered.
2. Throttle high side (climbing and diving from
hovering)
Repeat climbing and diving from hovering
at a constant rate matched to your own
rhythm and adjust the pitch so that the
nose does not deflect when the throttle is
raised and lowered.
However, when a GY Series or other heading
hold gyro is used, since correction is performed
by the gyro, this mix is not used. If this function
is used when the gyro operation mode is the
AVCS mode, the neutral position will change.
<Idle up condition mixing curve>
Set the mixing rate so that the rudder
direction at high-speed flight is straight
ahead. Adjust for each condition used.
<Acceleration function setting>
ŏ Acceleration operation can be performed
for both setting at acceleration (High)
and setting at deceleration (Low).
ŏ Acceleration rate setting (Rate)
ŏ The return time after operation (Damping)
can be set.
ŏ An operation point (Act position) at
acceleration and deceleration can be set
independently. When an operation point
was exceeded, acceleration operation is
performed.
ŏSelect [PitchńRudder]
at the model menu
and call the setup
screen shown.
● Mixing curve setting
*For a description of the
curve setting method,
see the description at
the back of this manual.
Normally, use [Point] type.
165


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX36 in the language / languages: English as an attachment in your email.

The manual is 11,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba FX36

Futaba FX36 User Manual - German - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info