747921

Futaba FX22 Manual

143
Zoom out
Zoom in
Previous page
1/174
Next page
143
<Model Menu (Airplane/Glider Functions)>
ŏ Select the function name
and return to the Model
menu by touching the
RTN button or pushing the
HOME/EXIT button.
<SensorTouch™>
RETURN
MOTOR
[Corresponding model type]: Airplane/glider, general
This function lets you set the speed when the
motor of an F5B or other EP glider is started via
a switch. The operation speed can be set for two
ranges, slow speed flight and high speed flight
(Speed 1/Speed 2). This function can also be
operated as a safety function by programming it to
a switch.
ŏ The In side and Out side operating speeds can
be adjusted independently in 2 ranges (Speed 1/
Speed 2).
ŏ The boundary between the 2 ranges can be set.
(From Speed 1 to Speed 2)
ŏ The operational speed can only be activated at
the initial operation. However, operation can be
repeated by setting the switch to OFF before the
operation is Ànished. When you want to reset one
time operation, set the ACT/INH item to [INH] and
then reset it to [ON].
ŏ The motor channel is controlled by SW-G. (Glider:
Initial setting) When changing the switch or stick
which controls the motor, Àrst change Function of
the Linkage menu.
ŏ If the Model Type selected is Airplane, the MOTOR
function is changed from INH to ON and it is not
assigned to another channel, the changes from
the throttle channel to the motor channel are
enabled.
Note: Initial setting does not assign a motor
channel according to the model type. Prior to
DVVLJQLQJWKHPRWRUFKDQQHOÀQGDQXQXVHG
channel. Then, use the Function menu of the
Linkage menu.
Set [Control] to the switch you want to use
and [Trim] to [--].
Note: When using this function, always check
the initial operation with the propeller
removed.
ŏ Select [MOTOR] at the Model menu
and access the setup screen shown
below by touching the RTN button.
Scrolling
ŏ Moving cursor
ŏ Selecting mode
ŏ Adjusting value
ŏ To next page
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
When using this function, move the cursor to
the [ACT/INH] item and touch the RTN button
to switch to the data input mode. Select the
[ACT] by scrolling the touch sensor and touch
the RTN button.
When selecting the ON/OFF switch, move the
cursor to the switch item and touch the RTN
button to access the selection screen. Select
the switch and set its ON direction. (Always
ON at "--" setting)
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0RWRURIISRVLWLRQVHWWLQJ
Move the cursor to the [MOTOR OFF] item
and touch the RTN button for one second
when the motor function switch (SG, etc.) is
in the motor OFF position you want to set. The
direction of the motor switch is memorized.
The screen graph display OFF direction also
changes.
Note:
ŏ)LUVWGHFLGHWKHPRWRU2))GLUHFWLRQDQGWKHQ
set the speed. When you want to reset the
motor OFF direction, also reset the speed.
ŏ:HUHFRPPHQGWKDW0RWRU2))EHVHWLQ
combination with F/S.
ŏ6HWWKHEDVLF RSHUDWLRQGLUHFWLRQZLWKWKH
Reverse function to match the ESC used.
ŏ$OZD\VVHWWKH0RWRU2))SRVLWLRQ
… 143 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FX22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FX22 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info