30094
8
Zoom out
Zoom in
Previous page
1/44
Next page
PROGRAMMED MIXING FAIL SAFE
Unidirectional mixing of any two channels desired
is possible using the pin board and jumper con-
nectors on the transmitter back panel. Either chan-
nel may be designated as "master" or "slave".
DSC
(Direct
Servo
Control)
Operation of the entire system with the transmit-
ter switch in OFF position is possible using the
DSC cord. This is useful for checking and adjusting
control movements on the ground while someone
else is flying on your frequency.
The Fail Safe function moves servos to a pre-set
position if the transmitter signal is lost or inter-
rupted by strong interferrence. The servos will be
held in the pre-set position until a proper signal is
again received at which time Fail Safe is released.
HOLD
The Hold function holds servos at the same posi-
tion
as
immediately prior
to
signal
interruption.
Hold is released when a proper signal is resumed.
•Trainer system offers an easy training of flight
for beginners.
•BASIC TRANSMITTER CONTROLS
The servo reversing switches are assumed to be in the normal position in the descrip-
tions in this section. When the reversing switches are in the reverse position, servo
operation is the opposite of that described here.
6
The names and functions of the transmitter
controls can be easily understood by read-
ing this section with the three-fold page at
the end of this manual unfolded.
1
Aileron stick
Controls the ailerons.
2
Elevator stick
Controls the elevators.
3
Throttle
lever
Controls the
throttle.
4
Rudder knob
Controls the rudder.
5 Landing gear switch Controls the landing gear.
6 Flap and flap trim control (CH6) knob
7 Spoiler (CH7) control knob
8 Pitch control (CH8) lever and pitch control
HIGH side trimmer
9 Idle-up lever
10 Flap, spoiler -> elevator (6, 7 -> 2) mixing
ON-
OFF switch
11 Throttle -> (flap. spoiler) -> elevator
(3 — 6. 7 ->
2) mixing / Throttle -> pitch control mixing
ON-OFF switch
12
Elevator -> flap
(2 -> 6) mixing ON-OFF switch
13 Snap Roll ON-OFF switch (self
off)
14 Aileron dual rate switch (2-stage)
15 Elevator dual rate switch
16 Rudder dual rate/Programmable mixing ON-
OFF switch
17 Aileron trim lever
18 Elevator trim lever
19 Throttle trim lever with ATL
20 Rudder trim lever
21 Tachometer/timer
The tachometer/timer has the following func-
tions:
1. TACHOMETER
• Measurement by external sensor
• Two blade propeller specifications
LOW range 100 to 30,000 rpm
Error 100 rpm
•HIGH
range
100
to
60,000
rpm
Error 200 rpm
2. UP
TIMER
• 0 to 60 minutes with seconds display
3. DOWN TIMER
• 60 to 0 minutes with seconds display
4. INTEGRATING TIMER
• 0 to 60 hours with minutes display
5. BATTERY ALARM
Alarm sounds when the transmitter Nicd
batteries approach the
usage
limit.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8SSAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8SSAP in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info