30088
9
Zoom out
Zoom in
Previous page
1/16
Next page
when desiring to make the spin and other steering
angles large, set it to ON and adjust the horn, ad-
justers, and trimmers for level flight.
When the dual travel switch is set to OFF, kick
up is set, and the steering angle becomes large.
•Aileron,
elevator,
and rudder
right
and left (UP.
DOWN) angle adjustment
[ATV (Adjustable Travel Volume)]
The aileron, elevator, and rudder steering angles
can be made small within the range of the hatched
lines in Fig. 6.
When the aileron right roll and left roll rates are
different, they can be made the same by adjusting
the and trimmers of Fig. 2.
This also applies to the elevator and rudder.
An
elevator UP and DOWN difference can also
be
provided for easier flying.
The elevator ATV trimmers are
point, linkage is extremely simple.
Dual travel is operative even at elevator and flap
mixing.
Use the CH6 flap trim lever of Fig. 1 to adjust
the flap neutral position. Use this trimmer is the
same manner as a trim lever (aileron trim and
elevator trim).
Mixing is released when the MIX switch is set to
the center position ( mark). The flap neutral
position is not changed at this time.
(NOTE) Channel 6 is for the flaps, but can also be
used as a spare channel. However, since the
travel range is slightly narrow, adjust the
linkage.
•Adjustment when mixing spoiler, etc. and flaps
(When using the flaps and spoiler as an air brake)
Connect the flap servo to channel 6 of the re-
ceiver and the spoiler servo to channel 7.
of Fig. 2.
The rudder ATV trimmers are
of
Fig. 2.
•Elevator and flap mixing adjustment
Connect the flap servo to channel 6 of the receiver.
When the MIX switch of Fig. 1 is set to
the elevator and flaps are mixed. Set the steering
When the MIX switch of Fig. 1 is set to
. the spoiler is mixed with the flaps. When
the CH7 switch of Fig. 1 is set to , the
spoiler and flaps are operated simultaneously.
The amount of mixing at this time is adjusted
with the trimmer of Fig. 2.
The direction and amount can also be set.
When the MIX switch is set from RELEASE
to , the flap neutral position may deviate.
If this occurs, adjust the NEUTRAL
trimmer of Fig. 2 so that the flap neutral position
does not change when the MIX switch is set to
any position.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP8JN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP8JN in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info