30066
3
Zoom out
Zoom in
Previous page
1/4
Next page
A common power supply regulator and diode may also be supplied with the speed controller, depending on the vehicle
kit. Since they cause a voltage drop, always remove them.
TO BUYERS OF THE FP-2GS (FP-R102GF)
When using a Futaba motor control amp instead of
the speed controller supplied with the vehicle, turn
off the ASP (Adjustable Safety Position) system as
shown in the figure.
R102GF ASP
release
connector
Insert the ASP release co-
nnector packed "with
the
set at this 2P connector
(male pins) on the
printed
wiring board.
Fig. 5
•Set the transmitter power switch to ON, then set the receiver
power switch to ON. The servos stop near the neutral position.
Operate the transmitter sticks and check if each servo faithfully
follows operation of the sticks.
•Connect the pushrod to each servo horn, then check if the direc-
tion of travel of each servo matches the transmitter operation.
•Operate each servo over its full travel and check if the pushrod
binds or is too loose. Applying unreasonable force to the servo
horn will adversely affect the servo and quickly drain the battery.
Be especially careful when using 8.4V.
•Always make the full stroke (including trim) of the servo horns
somewhat larger than the full travel. Adjust the servo horns so
that they move smoothly even when the trim lever and stick are
operated simultaneously in the same direction.
Be alert for noise.
Always solder a noise killing capacitor to the running motor. If
metal parts touch each other due to vibration, noise will be gener-
ated and cause the receiver servos to operate erroneously. We re-
commend the use of noiseless parts.
Even though the receiver antenna wire is long, do not cut
or
bundle it. The range of the radiowaves will be shortened.
A spare horn is provided. Use it as required.
•Wrap the receiver in sponge rubber and wrap rubber bands around
the sponge rubber. Mount the receiver so it is not exposed to vi-
bration, does not touch the frame, and does not move.
•When the receiver is installed on a board or used where it may be
splashed with mud and water, place it in a plastic bag, etc. and
wrap a rubber band around the open end of the bag to waterproof
and dustproof the receiver. After use, remove the receiver from
the bag to prevent condensation.
Use the rubber bands wrapped around the receiver to hold the
servo and switch leads.
•After mounting is complete, recheck each part, then check the
transmitting range by making the transmitter antenna as short as
possible and extending the receiver antenna fully and operating
the set from a distance of 20m to 30m. The movement of each
servo should follow the movement of the transmitter sticks.
•The crystal can be changed from the outside of the receiver case.
Always use a Futaba transmitter and receiver crystal pair as the
replacement crystals.
Fig.
6
Fig.
7
Install the servos firmly. Install the servo to the servo tray
as shown in the figure. In other cases, install the servo as
described in the model manufacturer's manual.
REPAIR SERVICE
When requesting repair of trouble that has occurred suddenly
of from long use, describe the trouble symptoms in as much
detail as possible.
This will facilitate detection of the trouble point and shorten
the repair period greatly.
Defects caused
by
faulty
materials
or
workmanship
will
be
corrected free of charge.
This limited warranty is null and void if the set has been tam-
pered with or disassembled.
Refer to warranty statement for details.
WORLD SALES & SERVICE FACILITIES
Australia: FUTABA SALES AUSTRALIA PTY. LTD., Lebanon:
MELBOURNE TEL: 211-4788
Argentine: MODELISMO AE RONAUTICO DEGA SRL. New Zealand:
BUENOS AIRES TEL: 393-2299
Canada: UDISCO LTD., MONTREAL
TEL: 481-8109 Norway:
Chile: HOBBY LANDIA, SANTIAGO
TEL: 743957 Singapore:
Denmark: FUTABA IMPORT DENMARK,
COPENHAGEN TEL: 02-91-0101 South Africa:
England: RIPMAX LIMITED, LONDON
TEL: 01-8048272 Spain:
Finland: NORETRON KY. HELSINKI
TEL: 90-488880 Sweden:
Greece: C. & G. MACR1YIANNIS CO., PIRAEUS
TEL: 021-3604391 or 021-41 76191 U.S.A.:
Hong Kong: RADAR CO. LTD. TEL: 3-680507
Italy: RADIOSISTEMI SRL, Carrara W.Germany:
TLX: 500494 FORTIMI
FAX: 0039-585-52247
KHAIRALLAH MODELCRAFT, BEIRUT
TEL: 326-681
AMALGAMATED WIRELESS
(AUSTRALIA) N.Z. LTD. WELLINGTON
TEL: 58-979
HARALD LYCHE CO. A/S, Drammen
TEL: (03) 8339 70
SINGAPORE HOBBY SUPPLIES
TEL: 533-0337
REDIPAK (PTY.) LTD.,
JOHANNESBURG TEL: 21-1511
HOBBY & TOY INTERNATIONAL,
VALENCIA TEL: (96) 357 23 93
RADIO CONTROL CENTER,
JONKOPING TEL: 036-145360
FUTABA CORPORATION OF AMERICA,
CALIFORNIA TEL: 213-537-9610
ROBBE MODELLSPORT GMBH,
GREBENHAIIM TEL; 06644-870
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP2GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP2GS in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info