30066
2
Zoom out
Zoom in
Previous page
1/4
Next page
•The
trim
lever
is
used
to fine
adjust
each
channel.
Use
it for
neutral adjustment and to correct the flying posture after
the mechanism has been installed. After test flight, operate
with the trim lever in the neutral position, as far as possible,
by correcting with the rod adjuster, etc.
•Since the elevator stick employs a self-neutral system, install
the sliding plate as shown in the figure when changing it to a
ratchet system. Then remove the strong spring attached to
the hook and replace it with the spring supplied as an ac-
cessory.
•When the transmitter is used with a tank, the direction of the
stick can be changed 90 degrees by removing the four rudder
stick mounting screws.
•To change the crystals, loosen the rear cover mounting screws,
remove the rear cover, and then replace the crystal. The
crystal is located at the left side of the printed wiring board.
The transmitter crystal is marked (T) and the receiver crystal
is marked (R). CAUTION: Frequency change has to be done
under the supervision of FCC licensed personnel.
(Engine control
trim)
Elevator trim
Elevator stick
(engine control
stick)
The batteries can be
easily loaded by
inserting them
four at
a time from the back.
Modification from self-neutral
system to ratchet system.
Install sliding plate
Replace with
weak spring
Fig.
3
Slide in the direction
of the arrow while
pushing here.
Rear cover mounting screws
Fig.
2
Fig.1
Rudder stick
Rudder
trim
Antenna
Level meter
Power switch
RECEIVER FP-R102GF AND SERVO FP-S128
The BEC mark is displayed on the front of the receiver of BEC (Battery
Eliminator Circuitry) system sets with a receiver with shared power supply
regulator.
Your NEW FUTABA Digital Proportional R/C system is guaran-
teed against defects in workmanship and material for 180 days
from the date of purchase when the attached registration card is
returned to us within ten days of purchase.
This Guarantee is null and void if the R/C system has been im-
properly handled, damaged in a crash, or tampered with and
does not cover the replacement of plastic housings or electronic
components damaged due to the use of improper voltages.
When service is required, please take your equipment to your
local authorized service station or ship it directly to us. All
postage, shipping, and insurance charges must be paid by the
user.
(3) When motor car uses an ordi-
nary common power supply
chassis
Red common 2P
connector
(Female pins)
Buy the red common 2P
connector from the kit
manufacturer and connect to
the controller.
Pin 1: Minus
Pin 2: Plus
The Futaba BEC (Battery Eliminator Circuitry) system and BEC
& ASP (Adjustable Safety Position) system can also use a com-
mon power supply with the conventional four penlight batteries
system (separate power supply).
Connect the servo and switch as
shown in the figure and extend
the transmitter and receiver ante-
nna fully.
Red common 2P
connector (male pins)
Antenna mire
Receiver FP-R102GF
Switch
ON
OFF
Steering servo
Throttle servo
Connection to this connector
(1)When chassis power supply of
engine or motor car is separate
Wrapped with
rubber band.
Red common 2P
connector
(Female pins)
Receiver crystal
Fig.
4
Connect to the red common
2P connector of the control-
ler.
Controller
Red common 2P
connector
(Female pins)
(2) When motor car uses a speci-
al 8EC system chassis (com-
mon power supply specifi-
cations)
(75MHz-OPTIONAL)
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP2GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP2GS in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info