29023
7
Zoom out
Zoom in
Previous page
1/8
Next page
•Set
the transmitter power switch
to
ON,
then
set
the
receiver
power
switch
to
ON.
The servos
stop
near
the
neutral
position. Operate the transmitter sticks and check if each servo faithfully follows operation of the sticks.
From transmitter
when
switch turned
on
From receiver when
switch turned off
Connect the pushrod to each servo horn, then check if the direction of travel of each servo matches the transmitter
Operation.
Vehicle also steers
to the right
When transmitter
stick lever set to the
right
Operate each servo over its full travel and check if the pushrod binds or is too loose. Applying unreasonable force to
the
servo
horn
will
adversely
affect the servo and
quickly
drain
the
battery.
Be
especially careful
when
using 8.4V.
•Always make the full stroke (including trim) of the servo horns somewhat larger than the full travel. Adjust the
servo horns so that they move smoothly even when the trim lever and stick are operated simultaneously in the same
direction.
Be alert for noise.
Always solder a noise killing capacitor to the running motor. If metal parts touch each other due to vibration, noise
will
be generated and
cause
the
receiver
servos
to
operate erroneously.
We
recommend
the
use
of
noiseless parts.
Even
though
the
receiver antenna
wire
is
long,
do
not
cut
or
bundle
it.
The range
of
the
radiowaves
will
be
shortened.
Receiver antenna
wire
- Wood screw
Install the servos firmly. Install
the servo to the servo tray as
shown in the figure. In other
cases, install the servo as des-
cribed in the model manufac-
turer's manual.
Rubber
bushing
Grommet
R102JE
Scissors
• A spare horn is provided. Use it as required.
•Wrap the receiver in sponge rubber and wrap rubber bands around the sponge rubber. Mount the receiver so it is
not exposed to vibration, does not touch the frame, and does not move.
•When the receiver is installed on a board or used where it may be splashed with mud and water, place it in a plastic
bag, etc. and wrap a rubber band around the open end of the bag to waterproof and dustproof the receiver. After use,
remove the receiver from the bag to prevent condensation.
Use the rubber bands wrapped around the receiver to hold the servo and switch leads.
•After mounting is complete, recheck each part, then check the transmitting range by making the transmitter antenna
as short as possible and extending the receiver antenna fully and operating the set from a distance of 20m to 30m. The
movement of each servo should follow the movement of the transmitter sticks.
The crystal can be changed from the outside of the receiver case. (Except 72/75MHz in U.S.A) Always use a Futaba
transmitter and receiver crystal pair as the replacement crystals.
6
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba ATTACK_SPORT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba ATTACK_SPORT in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info