29015
8
Zoom out
Zoom in
Previous page
1/12
Next page
•Operate each servo over its full travel and check if the pushrod binds or is too loose. Applying unreasonable force to
the
servo
horn
will
adversely
affect
the
servo
and quickly drain
the
battery.
Be
especially
careful
when using
8.4V.
•Always make the full stroke (including trim) of the servo horns somewhat larger than the full travel. Adjust the
servo horns so that they move smoothly even when the trim lever and stick are operated simultaneously in the same
direction.
Be
alert for noise.
Always solder a noise killing capacitor to the running motor. If metal parts touch each other due to vibration, noise
will
be generated and
cause
the receiver
servos
to
operate erroneously.
We
recommend the
use
of
noiseless
parts.
•Even
though the receiver antenna
wire
is
long,
do
not
cut
or
bundle
it.
The
range
of
the
radiowaves
will
be shortened.
Receiver antenna
wire
Wood screw
Rubber bushing
Grommet
Install
the
servos
firmly.
Install
the servo to the servo tray as
shown in the figure. In other
cases, install the servo as des-
cribed in the model manufac-
turer's manual.
R102GF
Scissors
A spare horn is provided. Use it as required.
•Wrap
the receiver
in
sponge
rubber and
wrap
rubber
bands
around
the
sponge
rubber.
Mount the
receiver
so
it
is
not exposed to vibration, does not touch the frame, and does not move.
•When
the
receiver
is
installed on
a
board or
used
where
it
may
be
splashed
with
mud
and
water,
place
it
in
a
plastic
bag, etc. and wrap a rubber band around the open end of the bag to waterproof and dustproof the receiver. After use,
remove the receiver from the bag to prevent condensation.
Use the rubber bands wrapped around the receiver to hold the servo and switch leads.
•After mounting is complete, recheck each part, then check the transmitting range by making the transmitter antenna
as short as possible and extending the receiver antenna fully and operating the set from a distance of 20m to 30m. The
movement of each servo should follow the movement of the transmitter sticks.
The crystal can be changed from the outside of the receiver case. Always use a Futaba transmitter and receiver crystal
pair as the replacement crystals.
•USING THE FREQUENCY FLAG
Insert the frequency flag
into the flag holder as
shown here.
72/75MHZ Flag
Staple or glue with cyano-
acrylate ribbon here.
The flag can be attached to
and removed from the end
of the antenna with one
touch.
The hook is for the optional neck strap. It is convenient when hanging the transmitter from your neck.
7
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba ATTACK_BFR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba ATTACK_BFR in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info