29053

Futaba 9ZHP_part2 Manual

31
Zoom out
Zoom in
Previous page
1/78
Next page
Helicopter Section
THROTTLE CURVE
(TCV)
This function programs throttle curves to per-
form hovering, loops, rolls, and other aerobatics in
the
different
flight
modes.
The
throttle
curve sets
the
servo
response
over
the
full
stroke
of
the
throttle
stick
by
a
13-point
curve.
The
low
side
rate can be input (point 7 is the reference). The
servo
delay
at
idle-up
and
other
flight
condition
switching can be programmed.
Setting Up The Throttle Curve Function
Throttle Curve Inputting
In the Condition Menu, press the
•TCV
key to get the
THR CURVE menu shown in the upper portion of the
figure below.
Curve setting
Low Side
Rate Setting
Delay Amount
Setting
Point Movement
To Next Screen
Return To
Condition Menu
To Preceding
Screen
Setting Point Selection (Points 1 to 13)
Press the B key to turn on the curve inputting
function. Use the movement keys
Q
and R to select the
point whose value is to be set. The
PT->
key increases
the point number by one, and the
<-PT
key reduces the
point number by one. The active point on the curve is
shown as a black dot.
Once you have selected the desired point on the curve,
you may input the rate with the rate setting keys
E
to
M . The number keys 0 through
100
input the value
directly. The + and - keys increase or decrease the
value by 0.5 with each button pressing (so it takes two
hits to see a number change because of numeric round-
ing).
You may set or reset each point on the curve by
repeating these steps for each point.
Low-Side Rate Adjustment
Press
the D key and
you
may
input
the rate
with
the
numeric keys
E to M.
You may set anywhere in the
range from 0 to 110% (initially the rate is set to 100%).
Delay setting
Shift to the next screen (the lower one in the figure)
by pressing the
NXT (P)
key. Enter the delay with the
rate setting keys E to M. The delay may be set from 0
to 100%, and is initially set to 0%.
Use the END (N) key to leave this menu.
Helicopter Section, Page 107
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9ZHP_part2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZHP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info