Manual Futaba 9ZAP_part2 (page 6 of 78) (English)

29045

Zoom out

Zoom in

1/78

Airplane Section

V-TAIL (VTL)

This

function

automatically

sets

up the PCM

1024Z to

control a V-tail airplane with combined

elevator

and rudder functions. It requires two

servos, one hooked up to receiver output CH2

(elevator 2/rudder) and the second plugged into

CH4 (elevator 2/rudder 1). The elevator and rud-

der deflection can be adjusted independently.

Setting Up V-Tail Mixing

Activation of command

In the Condition Menu, press the

VTL

key to get the

V-TAIL Mixing menu shown below. Use the A key

to activate mode setting, then press the ACT or INH

keys ( F and G) to activate or inhibit V-Tail Mixing.

Mode setting

Elevator 1

deflection angle

Rudder 1

deflection angle

Elevator 2

deflection

angle

Rudder

deflection angle

Return to

condition screen

Mode selection

Setting the Elevator Rates - 1 and 2

You now set the rate for Elevator 1. Press the B key

to activate rate setting for Elevator 1 and set the rate with

the numeric keys E to M . The number keys 0 through

100

input the value directly. The + and - keys in-

crease or decrease the value by 1. The +/- key may be

used to reverse the throw direction.

If you are not sure what you are changing, hold the

stick to one side and press different keys — if there is no

effect, move the elevator stick to the other side and con-

tinue. Your setting may vary from —100 to +100%, the

initial value is +50%.

Now set the rate for Elevator 2. Press the Q key to

activate Elevator 2 rate setting and set the rate with the

numeric keys as before.

Setting the Rudder Rates - 1 and 2

You now set the rate for Rudder 1. Press the C key to

activate rate setting for Rudder 1 and set the rate with the

numeric keys E to M as before.

If you are not sure what you are changing, hold the

rudder stick to one side and press different keys — if there

is no effect, move the rudder stick to the other side and

continue. The initial value is +50%, but your setting may

vary from -100 to +100%.

Now set the rate for Rudder 2. Press the P key to

activate Rudder 2 rate setting and set the rate with the

numeric keys as before.

Checking Your Work

After you have set up the V-Tail rates, be sure that

they move the correct directions. For up elevator com-

mand, both V-tails should move upward. For right rudder

command, the trailing edge of both surfaces should move

to the right. If they do not, use the +/- to reverse the

direction as needed.

Use the

END ( N)

key to leave this menu.

Airplane Section, Page 82

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9ZAP_part2 in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba 9ZAP_part2 Manual

Product: