29049

Futaba 9CPsuper Manual

45
Zoom out
Zoom in
Previous page
1/109
Next page
Using FLAPERON (ACRO/GLID ):
The FLAPERON mixing function uses one servo on each of the two ailerons, anduses them
for both aileron and flap function. For flap effect, the ailerons raise/lower simultaneously.
Of course, aileron function (moving in opposite directions) is also performed.
[Note] When changing the polarity of a rate, "change rate dir?" is displayed for a check.
Please set up after pressing DIAL for 1 second and canceling an alarm display. (GLID only)
Once FLAPERON is activated, any time you program CH6 or "flap" (ie. FLAP-ELEVATOR mixing), the radio commands both
servos to operate as flaps. The amount of travel available as flaps is independently adjustable in FLAPERON. A trimming
feature is also available (see FLAP-TRIM) to adjust both neutral positions together for straight-and-level flight or slight
increases/decreases of the flap angle.
Adjustability:
• Each aileron servo's up travel can be set separate from its down travel, creating aileron differential. (See example).
• Each aileron servo's travel when actuated as a flap is separately adjustable.
• AIL-2 can be utilized to use a 5-channel receiver and still have flaperons. NOTE: The AIL-2 function only commands
the channel 5 servo to operate with the aileron servo as ailerons, and to obey the primary flap control (travel adjusted
in FLAP-TRIM.) It does not provide full flap mix capability as when using a 6+ channel receiver and channel 6.
NOTE: Activating flaperons only makes the ailerons work as ailerons and tells the radio how far you want them to move
as flaps IF you then activate other programming that moves them as flaps.
FLAP-TRIM is the flap-trimming feature that allows the flaps to move in reaction to the channel 6 control. It is meant only
for trimming the flaps' center but can also be used as full flap control. (See p. 46).
AIRBRAKE is a feature that drops flaperons as flap, and also compensates with elevator if desired. (See p. 56).
FLAP-ELEVATOR would add elevator mixing into the flap movement from the flap dial after FLAP-TRIM is activated.
END POINT and SUB-TRIM both still adjust each servo individually.
GOAL of EXAMPLE: STEPS: INPUTS:
* If you receive an error message that OTHER WING MIXING IS ON, you must deactivate AIL-DIFF or ELEVON. see p. 44.
45
Activate twin aileron servos, FLAPERON.
Input 10% less down travel than up
travel (aileron differential) within the
FLAPERON programming. (Decrease right
aileronís down travel to 90%, decrease
left aileron=s down travel to 90%.)
Adjust total flap travel available to
50% of aileron travel available.
Where next?
Open the FLAPERON function.
Activate the function.
Optional: adjust the up/down travel
separately for the 2 servos.(Ex: 90%
down.)
Optional: adjust the aileron's travel
so they move as flaps. (Ex: each servo
flap travel to 50%.)
Close menu.
for 1 second.
(If basic, again.)
to FLAPERON.
*
AILERON STICK. to 90%.
A
ILERON STICK. to 90%.
to 50%.
to -50%.
Set FLAP-TRIM: see p. 46.
Set up AIRBRAKE mix: see p. 56.
Mix flaperon's flap motion to another inboard flap (plugged into aux1): see p. 54.
View additional model setups on the internet: www.futaba-rc.com/faq/faq-9c.html
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info