29007
15
Zoom out
Zoom in
Previous page
1/109
Next page
15
Stick tip ALocking piece B
Adjusting the length of the non-slip control sticks
You may change the length of the control sticks to make your transmitter more
comfortable to hold and operate. To lengthen or shorten your transmitter’s sticks,
first unlock the stick tip by holding locking piece B and turning stick tip A
counterclockwise. Next, move the locking piece B up or down (to lengthen or
shorten). When the length feels comfortable, lock the position by turning lock-
ing piece B counterclockwise.
Stick lever tension adjustment
You may adjust the tension of your sticks to provide the feel that you prefer for flying. To adjust your springs, you’ll have
to remove the rear case of the transmitter. First, remove the battery cover on the rear of the transmitter. Next, unplug the
battery wire, and remove the battery and RF module from the transmitter. While you are removing the RF module, pay
attention to the location of the pins that plug into the back of the module. Next, using a screwdriver, remove the four screws
that hold the transmitter’s rear cover in position, and put them in a safe place. Gently ease off the transmitter’s rear cover.
Now you’ll see the view shown in the figure above.
Using a small Phillips screwdriver, rotate the adjusting screw for each stick for the desired spring tension. The tension
increases when the adjusting screw is turned clockwise.
When you are satisfied with the spring tensions, reattach the transmitter's rear cover. Check that the upper printed circuit
board is on its locating pins, then very carefully reinstall the rear cover being mindful to guide the RF module connector
pins through the slot in the case. When the cover is properly in place, reinstall and tighten the four screws. Reinstall the
battery, cover and module.
Adjusting Display Contrast:
To adjust the display contrast, from tha home menu press and hold the End button.
Turn the dial while still holding the End button:
clockwise to brighten
counterclockwise to darken the display
Let go off the dial and the button.
Changing Modes:
Hold down the Mode and End buttons while turning on the Transmitter. The screen reads "STK-MODE". Change this to the
correct mode. Note that this will NOT change the throttle and elevator rachets, etc. Those are mechanical changes that
must be done by a service center.
[Note] While changing modes, the transmitter transmits in PPM mode even if the set-up mode is PCM mode.
CAMPac data conversion (9C to 9C super):
Hold down the Mode and End buttons while turning on the Transmitter. Select "T9C-Pac > UPDATE" by Cursol button.
Then press the Dial for 1 second for starting the data conversion. Note that the converted CAMPac cannot be used with a
conventional 9C transmitter.
[Note] While data conversion, the transmitter transmits in PPM mode even if the set-up mode is PCM mode.
Aileron
Elevator
Rudde
r
Stick Stick
Mode 2 transmitter with rear cover removed.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 9CAPsuper at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 9CAPsuper in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info