29001

Futaba 8UAPS Manual

79
Zoom out
Zoom in
Previous page
1/105
Next page
75
The TH-CUT function is used to kill the engine at the end of a flight. The engine
can be stopped with one touch with switch F (the momentary trainer switch is the
initial setting, but you may select another). This function eliminates the need to
move the trim to kill the engine and then move back to the idling position after each
flight. When the throttle stick is lower than the function ON/OFF set point throttle
position (normally a little above idle), the TH-CUT function responds to the operation
of the switch, and the throttle servo moves to its defined position.
The TH-CUT function will protect you from accidentally shutting off the engine.
When the throttle stick is above the set point, the TH-CUT function is not activated
even if the throttle cut switch is operated. In addition, you must move the throttle
stick back below the set point before the TH-CUT function can be reset, to avoid
sudden engine acceleration.
TH-CUT setup
Hook up and adjust the throttle linkage so that full throttle fully opens the
carburetor, and use the digital trim to make the engine idle at low throttle. Turn on
the throttle cut switch (switch F) and select the amount of offset to be just large
enough in the "–" direction (low throttle) to fully close the carburetor.
If you prefer, you may select another switch and ON-OFF direction. For safety,
always activate the TH-CUT function and use it.
Setting up the Throttle Cut function
1. Turn the TH-CUT function ON or OFF by pressing the
(+) key ("ON" or "OFF" displayed depending on switch F's
position). Turn off (INH) the function with the (-) key.
To MODEL
function
To TRAINR
function
Throttle position
Range: 0 - 100%
(Initial setting 5%)
Data input keys
These keys are used to move
through the five submenus in
the TH-CUT function.
2. Input throttle offset
Adjust the throttle offset amount
with the (+)/(-) keys.
• If you're unhappy with what you've
set, you may return to the default
value by pressing the (+) and (-)
keys simultaneously.
3. Throttle-Cut activation position
Hold the throttle stick at the highest
throttle location you want to be able
to activate TH-CUT (normally set
near idle). Memorize the position by
pressing the (+)/(-) keys
simultaneously.
4. Activation Switch Selection
Select the switch with the (+)/(-) keys.
5. Switch direction selection
Select the desired direction for the switch to turn the function on and
off with the (+)/(-) keys.
UP = Upper position turns on TH-CUT
DOWN = Lower position turns on TH-CUT
NULL = TH-CUT is deactivated
Switch direction display
(NULL, UP, DOWN)
Throttle Offset
Range: -30 to
+30%
(Initial setting 0%)
Selected
switch
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 8UAPS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 8UAPS in the language / languages: English as an attachment in your email.

The manual is 4,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info