28993

Futaba 6XH Manual

21
Zoom out
Zoom in
Previous page
1/64
Next page
AIRCRAFT SETUP INSTRUCTIONS (GENERAL 120 CLASS STUNT PLANE)
The aircraft setup procedure presented
below uses a F3A-class model as an example
and assumes that there are two aileron servos,
one in each wing. You may use a similar
procedure to set up your own model, but your
setting’s numbers and percentages will
probably be different.
1. Be sure that all of your servos are plugged
into the proper receiver channels:
CH1 — Aileron (Right aileron*)
CH2 — Elevator
CH3 — Throttle
CH4 — Rudder
CH5 — Gear
CH6 — Flap (Left aileron*)
* = if FLPR activated
We recommend that you begin your
programming exercise with the servos
installed in the model and connected to the
respective control surfaces. This will enable
you to immediately see the effect of each
programming action we're about to take.
2. Turn on your transmitter and receiver, and
select the desired model memory. To do this,
enter the programming mode by pressing the
two
MODE keys, then press the down MODE
key until “
MODL” appears. Press the CURSOR
key and choose a vacant model memory with
the plus (+) and minus (–)
DATA INPUT keys.
Select it by pressing the
CURSOR key until
“SET” is flashing, then press both the
DATA
INPUT
keys at once. The figure shows
memory #1 being utilized.
There are a number of ways to keep track of
which model is in each memory. You may
attach a small piece of white tape to the
transmitter front and write the model's name
along with the model setup number, or you
may use a notebook, or label the model with
its memory number prominently near its on-
off switch inside the fuselage.
3. Enter the Parameter (
PARA, p. 38) menu by
pressing the down
MODE key three times.
Press the key three times to select the ACRO
model type (four presses gets the HELI
function). Select ACRO by pressing both
DATA INPUT
keys. When the flashing “SET”
appears, again press both
DATA INPUT keys to
lock it in.
flashing
The reason for the separate functions within
the
PARA setup is that these are seldom used,
and the parameter menu provides a convenient
way of bypassing them for most programming
operations.
WARNING: selecting a different model type
will erase the settings in the model memory.
BE SURE you’re in the correct model
memory before selecting a new model type.
4. If your receiver happens to be different
than the transmission mode (as shown it’s
PPM), continue to the modulation (
MOD, p.
40) menu to select the proper mode of
transmission (
F is for FM/PPM transmission,
and
C is for PCM). This should be set to
match your receiver. If you make a change, it
won’t take effect until you cycle the power off
and on again. So if you have changed
modulation, cycle power now.
flashing
5. If your model has flaperons, turn on the
Flaperon function (FLPR, p. 28) in the menu.
To do this, press one of the
MODE buttons
until “
FLPR” appears in the display. Press the
CURSOR key to get the “INH” flashing, then
activate by pressing the plus (+)
DATA INPUT
– 16 –
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6XH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6XH in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 6XH

Futaba 6XH User Manual - Spanish - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info