28989
43
Zoom out
Zoom in
Previous page
1/64
Next page
correct for an undesired pitching tendency (the latter is described in the ACRO model setup
section).
Using the Programmable mixers
1. Call up the mixer screen by repeatedly pressing one of the MODE buttons
until the PMXI or PMX2 window appears. The default is for the function to
be inhibited. To activate, press the CURSOR key, then press the (+) DATA
INPUT
key. This will cause the flashing INH display to change to a
flashing ON display.
2. Now you’ll select the Master channel for the mixing, the channel that causes the mixing to
occur. Press the CURSOR key to get the little arrow above the channel numbers flashing on
and off, then press the (+) or (–) DATA INPUT keys to get to the number of the desired master
channel.
3. Next you’ll put in the Slave channel, the one that is affected by
motion of the master channel. Press the CURSOR key to get the little
arrow below the channel numbers flashing on and off, then press the
(+) or (–) DATA INPUT keys to get to the number of the desired slave channel.
Master
Slave
4. Now press the CURSOR key, this will cause the plus or minus sign in front of the large
number to flash on and off. You can set the direction the mixer works on each side of the
master channel’s control’s motion by changing this flashing sign with the (+) or (–) DATA
INPUT
keys. For example, for a model that pitches during knife-edge flight, you’ll want to
input either up or down elevator for either direction of full rudder. Therefore, you’ll either
set plus or minus for both sides of the master channel’s motion (indicated by the R/U or L/D
indicator in the window). Verify that you get the proper motion of the slave channel when
you move the master (don’t worry if the amount of travel is incorrect, you’ll set this in the
next step).
5. Again press the CURSOR key; this will cause the small percent sign in front of the large
number to flash on and off. At this point you choose the percentage of mixing for both
directions of motion of the master channel. You may set a value of 0% to 100% for each
direction by moving the master channel in both directions, one at a time, and changing the
percentage number to suit. Now verify that the slave channel responds both the correct
direction and amount for travel on both sides with the master control. If you wish to return
the mixing percentage to the default 50% value, press both the (+) and (–) keys
simultaneously.
– 38 –
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6XA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6XA in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 6XA

Futaba 6XA User Manual - Spanish - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info