28989
39
Zoom out
Zoom in
Previous page
1/64
Next page
ELVN — Elevon Mixing
The Elevon function should be used with delta wings, flying wings,
and other tailless aircraft whose layouts combine the aileron and elevator
functions, and requires one servo for each elevon. Connect the right
aileron to receiver CH1/AIL and the left aileron to CH2/ELE.
1CH
Aileron operation
Elevator operation
2CH
The amount of aileron and elevator response can be adjusted
independently. However, if you program in too much elevator or rudder
travel, the servos may reach their travel limits before full stick motion has
occurred. Therefore, you should keep the travel settings at 50% or below
and adjust the control linkages to get the travel you desire.
NOTE: The elevon, V-tail, and flaperon functions cannot be activated simultaneously.
The function activated last has priority.
Setting up elevon mixing
1. Use the up or down arrow keys to select the
ELVN
window.
2. Press the
CURSOR key three times to get to the activation setting. The INH
indicator will flash on and off.
3. Now press the (+) key to enable the elevon function. The display will
show a flashing ON.
4. Press the
CURSOR key once, to get to the aileron setting menu. A small
arrow is displayed over the numeral 1 (representing aileron master
channel), and the plus or minus sign above the large setting number will
blink on and off.
Move the aileron stick all the way to the right: the right elevon should move upwards, and
the left elevon should move downwards. If they move opposite to this, change the aileron
travel direction with the (+) and (–) keys. Note that this reverses the response at both elevon
servos (not just one as in the REV menu). If both servos move the same direction, reverse
the one that moves improperly in the REV menu.
5. Now you’ll input the amount of aileron travel by pressing the
CURSOR key once. Now the
percent sign will blink on and off, and you may adjust the amount of aileron travel with the
(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and
100% (press the plus and minus keys together if you wish to reset to 50%).
6. Next: the elevator inputs. Press the
CURSOR key once. A small arrow
should appear over the numeral 2 in the screen (indicating elevator is the
master channel), and the sign in front of the large setting number will flash
on and off. Verify that when you pull back on the elevator stick, both the elevon servos
move upwards. If they move the incorrect direction, change the direction by pressing the (+)
or (–) key which changes the flashing sign displayed.
7. Now you’ll input the amount of elevator travel by pressing the
CURSOR key once. Now the
percent sign will blink on and off, and you may adjust the amount of elevator travel with the
(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and
100% (press the plus and minus keys together if you wish to reset to 50%). Remember to be
sure not to have so much travel as to cause binding when both elevator and aileron are
commanded simultaneously.
– 34 –
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6XA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6XA in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 6XA

Futaba 6XA User Manual - Spanish - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info