28989
27
Zoom out
Zoom in
Previous page
1/64
Next page
you quickly want to get back to the default
100%, press both
DATA INPUT keys
simultaneously. We suggest using an initial
value of 75%, which will limit the aileron
travel to roughly 7/16” (11 mm).
NOTE: if you set the dual rate to 0%, you will
have ZERO CONTROL AUTHORITY when
the switch is in that position. DON’T DO IT!
26. Elevator dual rate setting: press the
CURSOR key one time to get the little arrows
above or below the numeral 2. Now set the
elevator dual rates in the same way you set the
ailerons. Adjust the up elevator travel to be
about 15/32” (12 mm) and the down elevator
travel to 17/32” (13 mm).
27. There is an option on the T6XAs/XHs
which allows you to put both dual rate
switches on the aileron D/R switch, or to keep
them on separate switches. This option is the
second item located in the
PARA menu.
If you choose the ‘2’ option as shown, both
dual rates will be operated by the aileron dual
rate switch. If you choose the ‘
1’ option, the
two D/Rs will operate off their individual
switches. We suggest the ‘
2’ option as it’s
one less switch to keep track of.
28. Airbrake (
ABRK, p. 30): an airbrake effect
is obtained by raising both ailerons (or
dropping the flaps) and adding elevator to
trim. This high-drag configuration makes the
landing approach steeper to help make safe
landings in small fields. With this function, it
is possible to lose some aileron effectiveness
so test the airbrake effect at altitude before
trying it on a landing approach. You should
spend some time fine adjusting the elevator
travel so that there is minimal trim change
when the airbrake switch is operated.
Press the
MODE SELECT button until the ABRK
window appears, as shown. The default is for
the airbrake mode to be inhibited, as shown.
To activate, press the
CURSOR
key until the
INH” is flashing, then press the (+) key.
Set mode with
DATA INPUT
keys:
+ = Activate
- = Inhibit
Now press the CURSOR
key one time, and the
percent symbol will flash. You may input the
amount of offset for the elevator (the arrow
should be under the numeral
2) at this time.
This should be set from -7% to -10% (-10% is
the default setting).
Press the
CURSOR key one more time, and
you may now input the CH6 setting. The rates
may vary considerably for different models,
but for initial settings choose the flap rate to
be (+)50-55%.
ON or OFF indicates
Airbrake switch position.
Increase or decrease
amount of travel with
DATA INPUT keys
AIR BRAKE
OFF side
ON side
29. Failsafe settings: we recommend that you
set the Fail Safe function (
F/S, p. 37) to move
the throttle to idle if interference is
experienced. Note that the failsafe function
only operates in the PCM transmission mode.
30. 2->6 Mixing: you may couple elevator to
flaps for tighter corners in the elevator-to-flap
mixer (2 -> 6, p. 35). Get to the
2->6 menu,
then activate it by pressing the
CURSOR key,
then the (+). Pull up elevator and verify that
the flaps go down. If they go the wrong
direction, reverse them by pressing the (+) or
– 22 –
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6XA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6XA in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba 6XA

Futaba 6XA User Manual - Spanish - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info