28983
18
Zoom out
Zoom in
Previous page
1/24
Next page
18
18
F/S Fail Safe
F/S Fail Safe
(PCM mode only)
(PCM mode only)
The Fail Safe function is used to prescribe what the PCM receiver will do in the event radio interference is received, and
doesn
t work FM(PPM) receivers. In this menu, you may select from one of two options of operation for each channel. The
“NOR”(normal) setting holds the servo in its last commanded position, while the “F/S”(Fail Safe) function moves each servo
to a predetermined position.
Throttle channel is set to
“F/S” as a default. All the other channels are set to “NOR”.
The use of the failsafe function is recommended from the standpoint of safety. You may wish to set the throttle channel so
that the throttle is moved to idle when there
s interference. This may give enough warning to allow you to fly towards yourself
and recover from the radio interference. If you choose to specify a failsafe setting, the failsafe data are automatically
transmitted once each minute.
Battery Failsafe
Battery Failsafe
Your system provides a second safety function called Battery Failsafe. When the airborne battery voltage drops below
approximately 3.8V, the battery fail safe function moves the throttle to a predetermined position or fast idle, if you haven
t set
it. If this happens, you should immediately land! If you need to increase throttle for your landing approach, you may
temporarily reset the failsafe function by moving the throttle stick to idle, after which youll have about 30 seconds of throttle
control before the battery function reactivates.
To set the Fail Safe Function:
To set the Fail Safe Function:
1. Enter the programming mode. Access the F/S
F/S
screen with the MODE key.
2. You can find the channel blinking on the left of the screen, which can be set to the Fail Safe.
The first channel you see is CH1 (aileron). Press DATA Input lever downward when you
need to set Fail Safe. The arrow moves to F/S side. This means this channel has been set
to F/S function. Then move the aileron stick to the position where you want the servo to
move when
F/S
F/S
function works and press DATA INPUT lever downward for about two
seconds while holding the stick. A figure in percentage will be shown with a beeping sound.
Press DATA INPUT lever upward if you want to set
NOR
NOR
. The arrow moves to NOR
NOR
side and then this channel will be set to NOR
NOR
function.
3. Carry out similar procedure like this in setting
“F/S” function for other channels. Use Mode
key to show a channel and do the same. But, CH3 (throttle) is set to 20% of the full throttle
for “F/S” function as a default.
4. Verify that your failsafe programming works by switching off transmitter power and observing the motion of the servos.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba 6EXAP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba 6EXAP in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info