522217
9
Zoom out
Zoom in
Previous page
1/21
Next page
Page 9
When the transfer is completed, remove the SD-Card or the Flash Drive from the
computer.
Note:
To safely remove the SD-Card or Flash Drive, return to the My Computer
window, right-click on the External Drive, then click Eject.
3. MM3D USB Hard-Drive Introduction
The MM3D external USB hard-drive contains chart data that can be used with NavNet
3D. The chart data can be copied onto SD-Cards (2GB SanDisk SD-Cards
recommended) or USB Flash Drive (MFDBB only) then installed into the NavNet 3D
MFD(s) using the integrated SD-Card reader of the display (MFD8/12) or USB2.0 port
(for the MFDBB).
Furuno USA strongly recommends the use of the external USB hard-drive as the
best method for loading chart data onto SD-Card(s)/Flash Drive.
All the Data contained in the “NOAA USA” folder can be installed into any NavNet 3D
display without unlock code (free data). The Data contained in the other folders can be
copied and distributed but will require an Unlock Code when installed into any NavNet
3D MFD.
Warning:
Do NOT rename or change the extension of any files contained on the
external USB hard-drive.
The instructions below explain how to transfer the Data from the external USB hard-
drive to the SD-Card(s) or Flash Drive. Please note that you can also transfer the entire
contents of the external USB hard-drive to a computer (this will improve the transfer
speed to the SD-Card)
Note:
PC Required. The external USB hard-drive cannot be connected directly to
NavNet 3D: SD-Cards or Flash Drive are required to transfer the data.
3.1. Connecting the Hard-Drive
Insert the USB cable of the external USB hard-drive directly into an available USB port
on your PC. The USB connection will be used to transfer data and power to the
external USB hard-drive (no extra power supply is required).
Note:
In the lower right-hand corner of your screen, you may see a message indicating
that a new device has been detected. It may take about 10 seconds until you see
“Device is ready for use.”
If the external drive folder doesn't automatically open, follow the instructions below:
Click Start and select “My Computer”.
Double-click your external hard-drive icon. The name of your external drive
may vary. For example: MM3D (D:) (see Figure 3.1):
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno NavNet 3D Chart Installation Guide v3.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno NavNet 3D Chart Installation Guide v3.0 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info