13373
50
Zoom out
Zoom in
Previous page
1/97
Next page
8. MENU SETTINGS
8-2
Geodetic datum
Select the geodetic chart system you are
using. WGS-84 (standard GPS chart system)
and NAD 27 can be directly selected. For
other charts, select "OTHER" and enter chart
number referring to the geodetic chart list in
the Appendix.
To output position data to ECDIS (Electronic
Chart Display and Information System), turn
on the power while holding down the [0] key.
This disables access to the Geodetic Datum
menu. Then, "Cannot be changed" is shown
in the Geodetic Datum menu as in Figure 8-2
on the next page. To stop outputting position
data to ECDIS, turn on the power while
holding down the [0] key.
Position offset
You may apply an offset to position
generated by the internal GPS receiver, to
compensate for difference between GPS
position and chart position.
Time difference
The GPS system uses UTC time. If you
would rather use local time, enter the
difference in hours between local time and
UTC. Use the numeric keys for times later or
earlier than UTC, respectively.
Position
When executing cold start there is no
satellite information in the unit’s memory,
thus it may take some time to find position.
To fix position faster, enter estimated
position.
Selecting fix mode
1) Press MENU ESC, 9 and 6 to display the
GPS SETUP menu.
Fix mode 2D 2/3D
Disable satellite 12
ANT Height 016 ft
(1-32)
GPS Smoothing
0 0 0 (0000-9999 sec)
Spd 0 0 0 5 (0000-9999 sec)
Speed Average 0 0 6 0 (0000-9999 sec)
To Next Page
GPS SETUP 1/2
MENU : Escape
: Select
ENT : Enter
Posn
0
Figure 8-1 GPS SETUP menu, page 1/2
2) Press
or to select Fix mode.
3) Press
or to select fix mode
desired.
4) Press
to change other settings, or
press MENU ESC key to register settings
and escape.
Disabling satellites
1) Press MENU ESC, 9 and 6.
2) Press
or to select Disable
satellite.
3) Key in satellite number, in two digits
(01-32). Three sets of satellite numbers
may be entered.
4) Press the NU/CU ENT key. If an invalid
number is entered the buzzer sounds.
5) Press the MENU ESC key.
Note: To enable all disabled satellites, press
the CLEAR key at step 3. All satellite
numbers on the Disable satellite line are
erased.
Entering GPS position smoothing
1) Press MENU ESC, 9 and 6.
2) Press
or to select Posn.
3) Enter smoothing factor in three digits
(0000-9999).
4) Press the NU/CU ENT key.
5) Press the MENU ESC key.
50


Need help? Post your question in this forum.

Forumrules
1

Forum

furuno-gp150

Reset search

  • Furuno GP-150. The gps date is suddenly changed to 2002 May 20.How can I change back the present date?
    Submitted on 4-1-2022 at 12:52

    Reply Report abuse
  • Furuno GP-150. The gps date is suddenly changed to 2002 May 20.How can I change back the present date? Submitted on 4-1-2022 at 01:07

    Reply Report abuse
  • How to setup the present date of GP150 GPS when suddenly changed of date automatically? Submitted on 3-1-2022 at 18:02

    Reply Report abuse
  • The gps date is suddenly changed to 2002 May19.How can I change back the present date? Submitted on 2-1-2022 at 10:48

    Reply Report abuse
  • The date is suddenly changed to 2002 May19.How to change back the present date? Submitted on 2-1-2022 at 10:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno GP150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno GP150 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info