28282
44
Zoom out
Zoom in
Previous page
1/63
Next page
33
¡. Nav Talker
2 . Depth Unit
3 . Temp Unit
4 . Hdg Sensor
5 . Key Beep
6 . Ant on Tx
7 . Dead Sector
8 . Tuned/Video
9 . Heading Alignment
10. Sweep Timing
11. MBS Adjustment
12. Ant Height
13. STC Curve
14. Ope Mode
15. Hours in Use
16. Tx Hours
Low
Mid
Hig
GPS
fa
˚F
Gyro
On
Stop
Std
Slave
All
m
˚C
Magnet
Off
Rotate
180˚~180˚
Sharp
Master
000001.5H
000000.0H
Gntl
LC
ft
[ Installation Setup ]
Select item by omnipad
and ress ENTER key.
Auto Adjustment
Adjustment
Figure 6-21 Installation setup menu
Adjusting tune/video
Do the following to adjust tune and video am-
plifier level input.
1. Press the [ST BY/TX] key to transmit.
WARNING
Before transmitting the radar make sure
no one is near the antenna unit, to pre-
vent the potential risk of being struck
by the rotating antenna and exposure
to RF radiation hazard.
2. On the Installation setup menu, select “8.
Tune/Video Adjustment” and press the
[ACQ/ENTER] key.
3. The unit automatically adjusts, displaying
the following message.
[ Tune/Video Auto Adjustment ]
Now under correction.
Return to illustration setup.
menu after the correction.
Figure 6-22 Tune/Video Auto
Adjustment messages
4. When adjustment is completed, the mes-
sages disappears.
Entering antenna height
The STC curve changes with respect to an-
tenna height above the waterline. Enter an-
tenna height above the waterline to optimize
the STC curve.
1. Select “12. Antenna Height” on the instal-
lation setup menu and press the [ACQ/EN-
TER] key.
2. Operate the omnipad to select antenna
height above the waterline; Low (~3 m),
Mid (3~6 m) or High (6~10 m).
3. Press the [ACQ/ENTER] key.
Aligning heading
(Adjustment sector:0~359.90)
You have mounted the antenna unit facing
straight ahead in the direction of the bow.
Therefore, a small but conspicuous target dead
ahead visually should appear on the heading
line (zero degrees).
In practice, you will probably observe some
small error on the display because of the dif-
ficulty in achieving accurate initial position-
ing of the antenna unit. The following
adjustment will compensate for this error.
1. Identify a suitable target (for example, ship
or buoy) at a range between 0.125 to 0.25
nautical miles, preferably near the head-
ing mark. To lessen error, keep echoes in
the outer half of the picture by changing
the range. Also, be sure the zoom and off
center functions are off.
2. Select “9. Heading Alignment” on the in-
stallation setup menu and press the [ACQ/
ENTER] key. The following message ap-
pears on the display.
[ Heading alignment ]
Set EBL1 to center of target
dead ahead and press ENTER.
Correction 0.0°
<Press MENU for inst setup>
Figure 6-23 Heading alignment message
3. Operate the omnipad to bisect target se-
lected at step 1 with the heading line.
4. Press the [ACQ/ENTER] key.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1942 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1942 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1942

Furuno 1942 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info