28260
52
Zoom out
Zoom in
Previous page
1/63
Next page
AP-6
Figure AP-4 Auto acquisition area
Follow the steps shown below to activate the
auto acquisition area;
1. Open the "ARP-10 MENU".
2. Select "8. Auto ACQ" by operating the
omnipad.
3. Operate the omnipad to select "On".
4. Press the [ACQ/ENTER] key.
5. Press the [MENU] key to close the menu.
Terminating Tracking of Targets
When the Auto Plotter has acquired 10 tar-
gets, no more acquisition occurs unless tar-
gets are lost. Should this happen, cancel
tracking of individual targets or all targets by
the procedure described below.
Individual Targets
Place the cursor (+) on a target which you do
not want to be tracked any longer by operat-
ing the omnipad and press and hold down the
[SELECT/CANCEL] key.
All Targets
All targets can be canceled from "ARP-10
MENU" at a time.
1. Open the "ARP-10 MENU".
2. Select "2. All Cancel".
3. Press the [ACQ/ENTER] key.
Displaying Target Data
The Auto Plotter calculates motion trends
(range, bearing, course, speed, CPA and
TCPA) of all targets under tracking at the ARP
Data area.
To turn ARP data on;
1. Press the [MENU] key.
2. Select the "DISP DATA".
3. Press the [ACQ/ENTER] key to select the
message for "ARP" or "NAV and ARP ".
4. Press the [ACQ/ENTER] key to set.
5. Press the [MENU] key to close the menu.
CAUTION
At the speed under 5 kts the target data is
displayed with a delay because of
filtration.
Place the cursor on a wanted target and press
the [SELECT/CANCEL] key. Data on the se-
lected target is displayed at the bottom of the
screen. The symbol of the selected target gets
twice as large as the normal circle. The data
includes the follows;
RNG/BRG (Range/Bearing): Range and
bearing from own ship to the last-plotted or
selected target position with suffix "T" (True)
or "M" (Magnetic). For true bearings suffix
"T" is used in case of gyrocompass input and
suffix "M" is used in case of magnetic com-
pass input.
COURSE/SPEED (Course/Speed):
Course and speed are displayed for the last-
plotted or selected target with suffix "T" (True)
or "M" (Magnetic). For true bearings suffix
"T" is used in case of gyrocompass input and
suffix "M" is used in case of magnetic com-
pass input.
CPA (Closest Point of Approach) is the clos-
est range a target will approach to own ship.
Do not mix it with the operator preset CPA
alarm limit.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1832 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1832

Furuno 1832 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info