28260
26
Zoom out
Zoom in
Previous page
1/63
Next page
15
3. Select 6. IntReject.
4. Select level desired by operating the
omnipad.
5. Press the [ACQ/ENTER] key.
6. Press the [MENU] key to close the menu.
IR and level selected appears at the bottom
right corner on the display when the interfer-
ence rejection circuit is turned on.
3.6 Selecting Pulsewidth
Pulsewidth is the transmission time of a single
radar pulse. The longer the pulsewidth the
greater the direction range capability, however
range accuracy and range resolution are re-
duced.
Pulsewidth can be selected to short or long
on the 1.5 and 3 nautical mile ranges.
1. Press the [MENU] key.
2. Select OTHER MENU and press the
[ACQ/ENTER] key.
3. Select 7. Pulselength.
4. Select Short or Long by pressing the
omnipad.
5. Press the [ACQ/ENTER] key to select.
6. Press the [MENU] key to close the menu.
3.7 Guard Alarm
The guard alarm allows the operator to set the
desired range and bearing for a guard zone.
When ships, islands, landmasses, etc. violate
the guard zone an audible alarm sounds and
the offending target brinks to call the
operators attention.
Selection of guard zone type
The guard alarm can be set to sound when a
target either enters or exits the guard zone.
You can select which type of guard alarm you
want through the menu.
In alarm
The alarm sounds on targets entering the guard
zone. G (IN) appears at the top right-hand
corner when the In alarm is selected.
Out alarm
The alarm sounds on targets exiting the guard
zone. G (OUT) appears at the top right-hand
corner when the Out alarm is selected.
IN ALARM
OUT ALARM
Guard
zone
Dashed line:
no alarm
Figure 3-7 In and Out alarm
Setting a guard zone
Preparation
1. Press the [MENU] key, and then select
OTHER MENU and pressing the [ACQ/
ENTER] key.
2. Select 17. Guard Mode and In (alarm
on target entering zone) or Out (alarm
on target exiting zone) by operating the
omnipad.
3. Press the [ACQ/ENTER] key.
4. Press the [MENU] key to close the menu.
To set a guard zone
1. Mentally create the guard zone you want
to set.
2. Operate the omnipad to set the cursor on
point A or B. Press the [GUARD] key. *G
(IN) or *G (OUT), with asterisk blink-
ing, appears at the top right-hand corner of
the display. See Figure 3-8 (2). (The aster-
isk indicates the guard zone is partially set.)
3. Operate the omnipad to set the cursor on
point C or D. See Figure 3-8 (3).
4. Press the [GUARD] key. The asterisk dis-
appears. See Figure 3-8 (4).
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1832 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1832

Furuno 1832 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info