596219
8
Zoom out
Zoom in
Previous page
1/27
Next page
2
Mounting on a platform
1. Remove mounting hardware at the bottom
of the antenna unit; four each of hex bolts
(M10X20), spring washers and flat washers.
Save mounting hardware to use it to fix the
antenna unit to the mounting platform later
on.
Flat washer
Spring washer
Hex bolt (M10 x 20)
Screws
two screws on other side
Bow
Stern
Figure 3 Antenna unit, showing location of
mounting hardware
2. Construct a platform (wood, steel, or
aluminum) of 5–10 mm in thickness
referring to the outline drawing at back of
this manual. Fasten the platform to the
mounting location. Next, position the base
so the cable entrance faces the stern
direction.
Note:
When drilling holes in the platform,
be sure they are parallel with the fore and
aft line.
3. Using the hex bolts, flat washers and
spring washers removed at step 1, fasten
the base to the platform.
The torque
should be between 19.6-24.5 N
m.
Note:
Longer hex bolts (M10X25) are
supplied with the installation materials. Use
them instead of the hex bolts removed
earlier if the mounting platform is very thick.
Flat
washer
Antenna base
assy.
Spring
washer
Platform
Hex bolt
(M10 x 25
or M10 x 20)
Transceiver
module
5-10
10-15
mm: M10x20
mm: M10x25
Figure 4 How to fasten the base to platform
4. Unfasten four screws to remove the cover.
Discard the packing material in the
radome.
Remove and discard
the packing material.
Snap holder
Figure 5 Antenna unit, inside view
The mounting base is fitted with a snap
holder. which may be used to hang the
cover after removal. Use the hole next to
screw hole inside the cover to hang it.
a) Unfasten the snap assy. with the string
attached at the holder in the mounting
base.
b) Unwind the string.
c) Attach the snap to a screw hole on the
inside of the cover.
Note:
Do not hang any other objects with the
snap.
5. Unfasten the cable of the rotation detector
from the cable clamps.
6. Unfasten 11 screws to dismount the shield
plate. Discard screw marked with
in the
Figure 6.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1712 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1712 in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1712

Furuno 1712 User Manual - English - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info