288584
52
Zoom out
Zoom in
Previous page
1/65
Next page
103
Connection
6
102
DISCONNECTING FROM THE PC
(
Important — always use this procedure.
)
Off
1Quit all applications (FinePixViewer, etc.) that
are using the camera.
2Check that the Access lamp is off (that the
camera and computer are no longer
exchanging data).
Perform the steps shown below before you switch the camera off. This procedure differs
depending on the operating system software (or PC) you are using.
!
In some cases, the camera and computer may still be communicating even after the Copying message
disappears from the computer screen. Always check that the Access lamp is off.
For a USB connection, no action is needed on the computer.
If you are connecting via an IEEE1394 interface, use the disconnection procedure described
below.
1Left-click the Eject icon in the taskbar and eject USB Disk.
2The Eject menu option is displayed. Click this menu option.
3The Eject hardware dialog box appears. Click the [OK] button or the close button.
Windows 98/98 SE
1
2
Windows Me/2000 Professional/XP
1Right-click the removable disk icon in the
My Computer window and select Eject.
3The Eject menu option is displayed.
Click this menu option.
4The Eject hardware dialog box appears.
Click the [OK] button or the close button.
2Left-click the Eject icon in the taskbar
and eject USB Disk.
Drag the Removable drive icon on the desktop to the Trash.
Macintosh
!
When you drag the icon to the Trash, REMOVE
OK appears on the cameras screen.
Switch the camera off and disconnect the IEEE1394 or USB cable.
3
This step is only required in
Windows Me.
Windows Me screen
CONNECTING TO A COMPUTER VIA USB
USB socket
Camera
1Load a media containing photographed
images into the camera.
2Switch the camera on.
3Select USB DOWNLOADING as the PC
MODE setting in SETUP (P.89).
4Set the power switch to OFF to switch the
camera off.
!
Before connecting, you must install software on the
bundled CD-ROM on your computer.
!
Use of the AC power adapter (sold separately) is
recommended when connecting the camera to a
computer.
!
If a SmartMedia and Microdrive are both loaded into the
camera at the same time, the media selected in the
MEDIA setting in SETUP is used (Setup, P.89).
2
1Switch your PC on.
2Connect the special USB cable to the camera
and the computer.
3Switch the camera on.
!
In Windows XP and Mac OS X, automatic startup must be set up the first time you connect.
!
Take care to ensure that the cable is connected the right way round and that the plugs are firmly inserted all
the way into the sockets.
Camera Operations
h When the camera and the computer are
exchanging data, the Access lamp blinks
orange.
h USB DOWNLOADING is displayed on the
rear display panel.
h The Auto Power Off function is disabled
while the camera is connected to a
computer.
!
When replacing the SmartMedia, always disconnect
the camera and computer first using the procedure
described on P.103.
!
Do not disconnect the USB cable during
communication. See P.103 for the disconnection
instructions.
USB
socket
PC
01
02
PC Operations
h If FinePixViewer is installed, it starts up
automatically.
h A removable disk icon appears and you
can use your PC to transfer files to and
from the camera.
1
FRAME NO.FRAME NO.
OFFOFF
SET−UPSET−UP
RESET ALLRESET ALL
BEEP♪BEEP♪
DATE/TIMEDATE/TIME
OKOK
SETSET
LOWLOW
PC MODEPC MODE
USB USB DOWNLOADINGDOWNLOADING
LANGUAGELANGUAGE
ENGLISHENGLISH
OKOK
BACKBACK
0201
03
Always use the prescribed procedure when
disconnecting or switching off the camera
(P.103).
If you are using a Windows PC, the driver settings are automatically specified when installation
ends. Simply wait a few moments.
If your computer does not recognize the camera, refer to the Software Quick Start Guide.
If the above operations do not occur, you do
not have the required software programs or
drivers installed on your PC. Refer to the
Software Quick Start Guide booklet and
complete the required PC setup procedures.
Then reconnect the camera to your PC.
Windows Macintosh
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujifilm finepix s 2 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujifilm finepix s 2 pro in the language / languages: English as an attachment in your email.

The manual is 4,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info