621646

Frilass 76059 Manual

18
Zoom out
Zoom in
Previous page
1/33
Next page
16
power supply after use.
3.0 PREPARATION
1. Ensure the machine is turned off.
2. Join the earth clamp to the workpiece to be welded. Never join the clamp to a
wooden bench or painted surface, in such cases there would be no current
induction.
3. The other end of the earth lead should be connected to the machine. This
should already be done.
4. Insert the electrode into the electrode holder. Ensure there is good connection,
the other end should be connected to the machine. Ensure welding surfaces
are kept clean.
5. Set amperage by regulating control wheel according to visual scale relating to
amperage/electrode diameter. This is shown on the front or side of the
machine.
3.1 YOU ARE NOW READY TO WELD
Switch on only when you are ready to start welding and the electrode is in position.
Practice on scrap metal first.
Tap the electrode lightly to strike arc and maintain a steady gap thereafter of about
2 mm between the end of the electrode and the metal being welded. Withdraw
with a clean movement at the end of the run.
You will notice a slight tendency to pull to the right. A few minutes practice will
ensure that you get used to this and compensate when doing a proper job.
If the electrode sticks you may be holding it too closely. Pull sharply to the left and
right to free it. After welding chip off slag with chipping hammer. You should wear
goggles when doing this.
4.0 IMPORTANT - THERMOSTAT CONTROL
Your welder is cooled by the circulation of air. If you use the machine with 16
gauge (1.5 mm rods) it will operate continuously. As larger diameter rods are used
you will experience the current being temporarily shut off. This is to protect your
transformer from overheating. Obviously the larger the rod the more current and
consequently the hotter the machine becomes.
The table below shows the number of electrodes which you can weld per hour.
The welder will produce up to 210 amps on 230 V power supply, depending on
welder size. When using larger electrodes or for better performance use 400 V 3-
phase. The position of the switch should be changed. Consult a qualified
electrician.
diameter
electrode
1.6 2 2.5 3.2 4 5
electrodes
per hour
112
-
60
75
48
55
28
33
14
18
8
12
current
(amps)
45
-
60
80
80
120
116
160
160
190
210
250
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frilass 76059 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frilass 76059 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info