590299

Frigidaire FPGH3077RF Manual

30
Zoom out
Zoom in
Previous page
1/36
Next page
30
CARE AND CLEANING
Cleaning the cooktop and surface burners
To avoid possible burns turn off all of the surface burners
and allow them to cool.
Any additions, changes or conversions required in order for
this appliance to satisfactorily meet the application needs
must be made by an authorized qualified agency.
Routinely clean the cooktop. Wipe with a clean, damp cloth
and wipe dry to avoid scratches. Keeping the surface
burner head ports and slots clean will prevent improper
ignition and an uneven flame.
To clean recessed and contoured areas of cooktop
If a spill occurs on or in the recessed or contoured areas,
blot up spill with an absorbent cloth. Rinse with a clean,
damp cloth and wipe dry.
To clean burner grates
• Clean when the grates are cool. Use nonabrasive
plastic scrubbing pad and mild abrasive cleanser.
• Food soils containing acids may affect the finish. Clean
immediately after the grates are cool. Thoroughly dry
grates immediately following cleaning.
To clean burner caps
• Remove caps from burner heads after they have
cooled. Clean heavy soils with a plastic scrubbing pad
and absorbent cloth. Thoroughly dry burner caps imme-
diately following cleaning including the bottom and
inside of cap.
• Do not use abrasive cleaners. Do not clean burner caps
in the dishwasher. Do not operate surface burners
without burner caps properly in place.
To clean the surface burner heads
For proper gas flow it may be necessary to clean the burner
head and slots. First use a clean damp cloth to soak up any
spills. Remove any food from between the burner slots
using a small nonabrasive brush like a toothbrush and wipe
up using a damp cloth. For stubborn soils located in the
slots, use a small-gauge wire or needle to clean. The
electrode must be carefully cleaned. Take care not to hit the
electrode with any thing hard or it could be damaged.
To clean the burner head ignition ports
Each burner head has a small ignition port (Figure 38).
Should you experience ignition problems it may be that this
port hole is partially blocked with soil. With the burner head
in place, use a small wire gauge needle or the end of a
paper clip to clear the ignition port.
Replacing the oven light
The interior oven lights are located at the rear of the oven
cavity and are covered with glass shields. The glass shield
must be in place whenever the oven is in use (Figure 39).
1. Turn electrical power off at the main source or unplug
the appliance.
2. Remove interior oven light shield by turning the shield
gently counter-clockwise and pull the shield straight out.
Do not twist or turn.
3. Replace bulb with a new appliance bulb. Replace glass
oven light shield.
4. Turn power back on again at the main source (or plug
the appliance back in). Be sure to reset the time of day
on the clock.
Figure 38: Gas burner head parts
Be sure the oven is unplugged and all parts are cool
before replacing oven light.
Figure 39: Oven light protected by glass shield
slots
ignition port
orice port
CAUTION
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frigidaire FPGH3077RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frigidaire FPGH3077RF in the language / languages: English as an attachment in your email.

The manual is 15,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info