590299
35
Zoom out
Zoom in
Previous page
1/36
Next page
35
BEFORE YOU CALL
Oven control panel sounds an
audible alarm and displays an
Error code.
Oven control has detected a fault or error condition. Turn either oven mode or tempera-
ture selector to the OFF position to clear the error code. Try Bake or Broil function. If
the Error code error repeats, turn OFF power to appliance, wait 5 minutes and then
repower appliance. Set clock with correct time of day. Try Bake or Broil function again.
If fault recurs, turn oven mode and temperature selectors OFF and call 1-800-4-MY-
HOME® for assistance.
Soil not completely removed after
Clean
Clean was interrupted. Review instructions in Clean section.
Excessive spills on oven bottom. Clean before starting Clean.
Failure to clean soil from the oven frame, the door liner outside the oven door gasket
and the small area at the front center of the oven bottom. These areas are not in the
self-cleaning area, but get hot enough to burn on residue. Clean these areas before
starting the clean cycle. Burned-on residue can be cleaned with a stiff nylon brush and
water or a nylon scrubber. Be careful not to damage the oven gasket.
Convection fan does not rotate. Oven door is open. Convection fan will turn off if oven door is opened when Convection
is active. Close oven door.
The convection fan will turn on after the oven has been heating for 6 minutes, and
remain on during the cooking process.
Clean does not work. Oven control not set properly. Review instructions in Clean section.
Surface burners do not ignite. Surface control knob was not completely turned to Lite. Push in and turn the surface
control knob to Lite until burner ignites and then turn control knob to desired flame size.
Burner ports are clogged. With the burner OFF, use a small-gauge wire or needle to
burner head slots and ignition ports.
Range power cord is disconnected from outlet (electric ignition models only). Be sure
power cord is securely plugged into the power outlet. Electrical power outage. Burners
may be lit manually. See “Operating the gas surface controls” on page page 9.
Surface burner flame uneven or
only part way around the burner
cap.
Burner slots or ports are clogged. With the surface burner OFF, clean ports with a small
gauge wire or needle.
Moisture is present after cleaning. Lightly fan the flame and allow burner to operate
until flame is full.
Burner caps are not seated properly. Check that all burner caps are level and seated
correctly on burner heads.
Surface burner flame is too high. Surface control knob is set too high. Adjust to lower flame setting.
Burner caps are not seated properly. Check that all surface burner caps are level and
seated correctly on surface burner heads.
Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frigidaire FPGH3077RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frigidaire FPGH3077RF in the language / languages: English as an attachment in your email.

The manual is 15,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info