613170

Friedland SA5 Manual

22
Zoom out
Zoom in
Previous page
1/52
Next page
INSTALLATION
20 SA5
TESTING THE SYSTEM
INITIAL TESTING
As the system is initially installed it is recommended
that each device is tested in turn as it is installed, (refer
to testing instructions for particular device).
TESTING AN INSTALLED SYSTEM
The Control Panel has a built in test facility to enable
you to test the system at any time. However it is
recommended that the system is tested at regular
intervals not exceeding 3 months.
With the system in Standby Mode
Press , ,
The Arm and Part-Arm LEDs will flash.
The system is now in the Test Mode
Use the and buttons to scroll through
the menu and press to select the displayed test
function or sub-menu.
Note: After completing all required test functions
press to leave Test mode and return to Standby.
WALK TEST
Before commencing testing please ensure that there
is no movement in any PIR protected area, all
doors/windows protected by Magnetic Contact
Detectors are closed and that all battery covers and
housings are correctly fitted.
Scroll through the top level Test Mode menu until
‘WALK TEST’ is displayed and press .
‘Walk Test Waiting…’ will be displayed.
1
.Trigger each detector on the system by either
walking into a PIR protected area or by opening a
door/window protected by a Magnetic Contact
detector. As each detector is triggered the Control
Panel will beep to indicate that an alarm signal has
been received and the identity of the zone that the
detector is configured for will be displayed.
Note: To conserve power and maximise battery
life the PIR detector will only detect movement if
there has been no movement detected within the
previous 2 minutes.
2
. Operate detector anti-tamper switches by opening
the case of the device. As the switches are
then remove the DC power jack and disconnect one of
the back-up batteries.
The hardwired zone and tamper switches should be
Volt free and Normally Closed, with the contacts
opening in order to initiate an alarm.
Note: Jumper link P51 should be fitted into the ON
position only if the external hardwired tamper circuit is
used, otherwise it must be in the OFF position.
After making your external connections reconnect the
power supply and Back-up Battery. Then close the
Control Panel cover and tighten the fixing screws on
the top edge of the Control Panel.
Press to leave Test mode and return to
Standby.
? ? ? ?
ENTER
User Access Code
ENTER
ENTER
ESC
ESC
press ENTER
Relay Test
Replay ON for 5s
Stop->ESC
Wirefree Siren
Test
Hardwired Siren
Test
WALK TEST
TEST MODE
Code:
Voice Dialler
Test
Test phone No._
Stop->ESC
Remote Manager
Test
ALARM TEST
Walk Test
Waiting…
Wirefree Siren
Service ON/OFF
Service ON/OFF
Wait for 10s
press ENTER
press ENTER press ENTER press ENTER
press ENTER
press ENTER press ENTER
Siren ON for 5s
Stop->ESC
Siren ON for 5s
Stop->ESC
Remote Manager
Test…wait
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland SA5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland SA5 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info