613170

Friedland SA5 Manual

13
Zoom out
Zoom in
Previous page
1/52
Next page
INSTALLATION
IMPORTANT: Take care when connecting battery
leads to the batteries as connecting incorrectly
could damage the batteries or the Control Panel.
Note: The Power LED may flash to indicate that
the unit is being operated from the back-up
batteries and that mains supply is not present.
9. If fitted, remove the plastic film covering the LCD
display and on the display window on the cover.
10.
Close the lid of the Control Panel and tighten the
captive fixing screws.
11.
Plug in and switch ON the Power Supply Unit, (the
Power LED should illuminate).
12.
If required, connect the Control Panel to the
telephone line using the cable supplied by
inserting small RJ11 plug into socket marked LINE
located on the bottom edge of the Control Panel.
If the cable supplied is not long enough to reach a
suitable phone point then it will need extending
using a coupler and extension lead (not supplied).
Note: If the Panel Tamper alarm sounds during the
installation reset the alarm by pressing:
, ,
on the Control Panel Keypad.
CONFIGURING THE CONTROL PANEL
HOUSE CODE
With unit in Standby mode (Power LED only
illuminated).
1. Press
, ,
‘1. USER SETUP’ will be displayed.
This puts the Control Panel into programming
mode.
2. Use the and buttons to scroll
through the menu until ‘2. SYSTEM SETUP’ is
displayed and press .
‘2. SYSTEM SETUP’ is displayed.
3. Press
The current House code setting will be displayed.
4. The new system House Code can be programmed
either directly at the Control Panel or via a Remote
Control Unit.
At the Control Panel:
Press buttons 1-8 on the Control Panel to configure
the display so that the required house code is
displayed on the screen. As each button is pressed
the corresponding digit in the house code will
change to the opposite state, (“0” or “1”).
1=House Code DIP Switch On/Up
0=House Code DIP Switch Off/Down
Using a Remote Control:
With the required House Code already configured
on the Remote Control, press .
The Control Panel will beep twice to acknowledge
the signal. The display will change to show
the received house code on lower line of the
display beneath the corresponding DIP switch
numbers (1-8).
5. Press to save the new setting.
6. Press , to return to Standby mode.
TESTING THE CONTROL PANEL
& REMOTE CONTROL
1. Press
, ,
to put the system into Test mode.
‘TEST MODE – WALK TEST’ will be displayed.
2.
Press to activate Walk Test.
‘Walk Test Waiting…’ will be displayed.
3.
Press the buttons on the Remote Control in turn,
as each button is pressed the Control Panel will
beep and display the function of the button being
pressed on the screen.
4. Test the range of the Remote Control by pressing the
‘DISARM’ button on the Remote Control from in and
around the property and from all locations where
you plan to install detectors. Check that the Control
Panel acknowledges the signal from the Remote
Control each time the ‘DISARM’ button is pressed.
5. Press to return to the top level menu of
TEST MODE.
ENTER
ESC ESC
1
2
3 4
ENTER
ENTER
ENTER
SA5 11
User Access Code
1
2
3 4
ENTER
ENTER
User Access Code
1
2
3 4
ENTER
Master User Access Code
ESC
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland SA5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland SA5 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info