560834

Friedland GlobalGuard Home Alarm System Manual

24
Zoom out
Zoom in
Previous page
1/232
Next page
24
7 Operation
When leaving the premises, the system must be armed. Before arming the system, make sure that all doors and windows are
locked and that the available PIR movement detectors are not obstructed. Make sure that animals are restricted to areas not
protected by PIR movement detectors.
The system has four arming modes: “Fully Arm”, “Holiday Arm”, “Part Arm-I” and “Part Arm-II”.
The “Holiday Arm” mode is a duplicate of the “Fully Arm” mode. The “Fully Arm” mode is commonly used daily, whereas the
“Holiday Arm” mode is used when away on holiday for a longer period. For the “Holiday Arm” mode particularly, you can set up
schedules or events to operate any home automation control receiver to simulate the presence of occupants. For details on
setting up schedules or events, refer to the software manual.
“Part Arm-I” and “Part Arm-II” allow for selected detectors or zones to be disarmed while other detectors or zones are armed.
When the system is armed, the display shows the arming mode and the programmed exit delay counting down. If the exit delay
beeps are enabled, the control panel will emit beeps with the beep rate increasing in steps as the exit delay expires. At the end
of the exit period, all active zones are fully armed. The user must have left the premises and closed the final protected door.
When the system is armed and a detector on an active zone is triggered, the display shows the programmed entry delay for the
zone counting down. If the entry delay beeps are enabled, the control panel will emit beeps with the beep rate increasing in
steps as the entry delay expires. If the system has not been disarmed when the entry delay expires, a full alarm will occur.
Details of the zone event that triggered the alarm are recorded in the event log.
At the end of the alarm time, the alarms will stop and the system will re-arm itself automatically (subject to the conditions of
the zone lockout feature).
7.1 Fully arming the system (“Fully Arm” mode)
Remote control
Control panel
1. Press the button once.
1. Press the button once.
2. Enter the 4-digit PIN code (User).
3. Press the button.
7.2 Holiday arming the system (“Holiday Arm” mode)
Remote control
Control panel
1. Press the button twice.
1. Press the button twice.
2. Enter the 4-digit PIN code (User).
3. Press the button.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland GlobalGuard Home Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland GlobalGuard Home Alarm System in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Friedland GlobalGuard Home Alarm System

Friedland GlobalGuard Home Alarm System Installation Guide - English, German, Dutch, French, Italian, Portuguese, Spanish - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info