787197
7
Zoom out
Zoom in
Previous page
1/8
Next page
For ceiling mounted installation, the available mount
angles are restricted to 0°, 15° and 30° only.
For wall mounted installation, the available mount angles
are restricted to 15°, 30° and 45° only.
7. Hang the heater on the brackets and firmly secure in
place with the mounting bracket locking plates by
tightening bolts.
NOTE:
Depending on material and design of ceiling structural
elements, the heater must be secured with the correct
fasteners. The weight of the heater is up to 5.3Kg, the
installation location must be able to hold 5 times the
weight of the heater.
CONNECTION TO ELECTRIC MAINS:
The heater is designed for connection to the single-phase
230-240V~ 50Hz electric mains equipped with an earth
wire.
Before connection, make sure that specifications of the
electric mains at the connection point meet the single-
phase 230-240V~ 50Hz voltage.
Regarding the model IHGB/W12SR
In case of direct connection to the supply line, a bipolar
switch or a bipolar circuit breaker with contact opening
distance of at least 3mm must be fitted upstream from the
supply line. Contact an authorized service technician if you
are unsure if you have a switch or a circuit breaker installed
on the premises.
The electric mains should be equipped with an automatic
circuit breaker with C curve type (slow blow fuse) and with
rated current not less than 10A (model 1500W) or 16A
(model 2200W). Contact an authorized service technician if
you are unsure if you have a circuit breaker installed on the
premises
The electric mains should be equipped with an automatic
circuit breaker with rated current not less than 16A..
The heater must not be located immediately below a
power point. Power point should not be located at the back
of the heater. The power point needs to be located outside
the physical footprint of the heater to minimize heat build-
up behind the heater.
If the heater is to be mounted on an incline (eg. Vaulted
ceiling), ensure the power point located at that lowest point
of the heater.
WIRING SCHEMATIC DIAGRAM:
IHGB/W12SR:
IHGB/W15S, IHGB/W22S:
Model No
“B” (mm)
MINIMUM DISTANCE
1200W
300±20
1500W
500 ±50
2200W
500 ±50
GB
EN
14
Wall Ceiling
Correct Installation Incorrect Installation
IN-L
IN-N
OUT-L
Heating Element
1200W
Heating Element
Switch
1500W
2200W
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frico Infraglas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frico Infraglas in the language / languages: English as an attachment in your email.

The manual is 0.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Frico Infraglas

Frico Infraglas User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info